Cisco Web Security Appliance
Security Target
Version 1.0
September 13, 2017
2
Table of Contents
1 SECURITY TARGET INTRODUCTION................................................................................7
1.1 ST and TOE Reference ...................................................................................................... 7
1.2 TOE Overview................................................................................................................... 7
1.2.1 TOE Product Type ...................................................................................................... 7
1.2.2 Supported non-TOE Hardware/ Software/ Firmware................................................. 8
1.3 TOE DESCRIPTION......................................................................................................... 9
1.4 TOE Evaluated Configuration ......................................................................................... 10
1.5 Physical Scope of the TOE .............................................................................................. 11
1.6 Logical Scope of the TOE................................................................................................ 14
1.6.1 Security Audit........................................................................................................... 14
1.6.2 Cryptographic Support.............................................................................................. 14
1.6.3 Identification and authentication............................................................................... 16
1.6.4 Security Management ............................................................................................... 16
1.6.5 Protection of the TSF................................................................................................ 17
1.6.6 TOE Access .............................................................................................................. 17
1.6.7 Trusted path/Channels .............................................................................................. 17
1.7 Excluded Functionality.................................................................................................... 17
2 Conformance Claims...............................................................................................................19
2.1 Common Criteria Conformance Claim............................................................................ 19
2.2 Protection Profile Conformance ...................................................................................... 19
2.3 Protection Profile Conformance Claim Rationale ........................................................... 19
2.3.1 TOE Appropriateness................................................................................................ 19
2.3.2 TOE Security Problem Definition Consistency........................................................ 19
2.3.3 Statement of Security Requirements Consistency.................................................... 19
3 SECURITY PROBLEM DEFINITION ..................................................................................20
3.1 Assumptions..................................................................................................................... 20
3.2 Threats.............................................................................................................................. 21
3.3 Organizational Security Policies...................................................................................... 22
4 SECURITY OBJECTIVES .....................................................................................................24
4.1 Security Objectives for the TOE...................................................................................... 24
4.2 Security Objectives for the Environment......................................................................... 24
5 SECURITY REQUIREMENTS..............................................................................................25
5.1 Conventions ..................................................................................................................... 25
5.2 TOE Security Functional Requirements .......................................................................... 25
5.3 SFRs Drawn from NDcPP ONLY ................................................................................... 26
5.3.1 Security audit (FAU)................................................................................................. 26
5.3.2 Cryptographic Support (FCS)................................................................................... 28
5.3.3 Identification and authentication (FIA) .................................................................... 32
5.3.4 Security management (FMT).................................................................................... 34
5.3.5 Protection of the TSF (FPT) ..................................................................................... 35
5.3.6 TOE Access (FTA) ................................................................................................... 36
5.3.7 Trusted Path/Channels (FTP).................................................................................... 36
5.4 TOE SFR Dependencies Rationale for SFRs Found in NDcPP ...................................... 37
3
5.5 Security Assurance Requirements ................................................................................... 37
5.5.1 SAR Requirements.................................................................................................... 37
5.5.2 Security Assurance Requirements Rationale............................................................ 38
5.6 Assurance Measures......................................................................................................... 38
6 TOE Summary Specification...................................................................................................39
6.1 TOE Security Functional Requirement Measures ........................................................... 39
7 Annex A: Key Zeroization ......................................................................................................52
7.1 Key Zeroization ............................................................................................................... 52
Annex B: References .....................................................................................................................53
Annex C: Technical Decisions.......................................................................................................54
4
List of Tables
TABLE 1 ACRONYMS............................................................................................................................................................................................ 5
TABLE 2 TERMINOLOGY ..................................................................................................................................................................................... 5
TABLE 3 ST AND TOE IDENTIFICATION.......................................................................................................................................................... 7
TABLE 4: IT ENVIRONMENT COMPONENTS..................................................................................................................................................... 8
TABLE 5 TOE MODELS AND SPECIFICATIONS...............................................................................................................................................11
TABLE 6 CAVP REFERENCES...........................................................................................................................................................................14
TABLE 7 TOE PROVIDED CRYPTOGRAPHY ...................................................................................................................................................15
TABLE 8 EXCLUDED FUNCTIONALITY ............................................................................................................................................................17
TABLE 9 PROTECTION PROFILES.....................................................................................................................................................................19
TABLE 10 TOE ASSUMPTIONS ........................................................................................................................................................................20
TABLE 11 THREATS..........................................................................................................................................................................................21
TABLE 12 ORGANIZATIONAL SECURITY POLICIES.......................................................................................................................................22
TABLE 13 SECURITY OBJECTIVES FOR THE ENVIRONMENT........................................................................................................................24
TABLE 14 SECURITY FUNCTIONAL REQUIREMENTS....................................................................................................................................25
TABLE 15 AUDITABLE EVENTS.......................................................................................................................................................................27
TABLE 16: ASSURANCE MEASURES.................................................................................................................................................................37
TABLE 17 ASSURANCE MEASURES..................................................................................................................................................................38
TABLE 18 HOW TOE SFRS ARE MET ............................................................................................................................................................39
TABLE 19: TOE KEY ZEROIZATION................................................................................................................................................................52
TABLE 20: REFERENCES ...................................................................................................................................................................................53
TABLE 21 NDCPP TECHNICAL DECISIONS....................................................................................................................................................54
List of Figures
FIGURE 1 TOE EXAMPLE DEPLOYMENT .......................................................................................................................................................10
5
Acronyms
The following acronyms and abbreviations are common and may be used in this Security Target:
Table 1 Acronyms
Acronyms /
Abbreviations
Definition
ACL Access Control Lists
AES Advanced Encryption Standard
CC Common Criteria for Information Technology Security Evaluation
CEM Common Evaluation Methodology for Information Technology Security
CM Configuration Management
DHCP Dynamic Host Configuration Protocol
HTTP Hyper-Text Transport Protocol
HTTPS Hyper-Text Transport Protocol Secure
ICMP Internet Control Message Protocol
IT Information Technology
NDcPP Network Device Protection Profile
OS Operating System
PP Protection Profile
SHS Secure Hash Standard
SIO Cisco Security Intelligence
SIP Session Initiation Protocol
SSHv2 Secure Shell (version 2)
ST Security Target
TCP Transport Control Protocol
TOE Target of Evaluation
TSC TSF Scope of Control
TSF TOE Security Function
TSP TOE Security Policy
WSA Web Security Appliance
Terminology
Table 2 Terminology
Term Definition
Authorized
Administrator
Any user which has been assigned to a privilege level that is permitted to perform all TSF-
related functions.
Role An assigned role gives a user varying access to the management of the TOE.
Security
Administrator
Synonymous with Authorized Administrator for the purposes of this evaluation.
User Any entity (human user or external IT entity) outside the TOE that interacts with the TOE.
Vty vty is a term used by Cisco to describe a single terminal (whereas Terminal is more of a verb or
general action term).
6
DOCUMENT INTRODUCTION
Prepared By:
Cisco Systems, Inc.
170 West Tasman Dr.
San Jose, CA 95134
This document provides the basis for an evaluation of a specific Target of Evaluation (TOE), the
Web Security Appliance (WSA). This Security Target (ST) defines a set of assumptions about
the aspects of the environment, a list of threats that the product intends to counter, a set of
security objectives, a set of security requirements, and the IT security functions provided by the
TOE which meet the set of requirements. Administrators of the TOE will be referred to as
administrators, Authorized Administrators, TOE administrators, semi-privileged, privileged
administrators, and security administrators in this document. The Common Criteria Functional
Specification is met through the description of interfaces in this Security Target and the
parameters described within the Common Criteria Guidance Documentation as well as the Cisco
documentation for WSA.
7
1 SECURITY TARGET INTRODUCTION
The Security Target contains the following sections:
 Security Target Introduction [Section 1]
 Conformance Claims [Section 2]
 Security Problem Definition [Section 3]
 Security Objectives [Section 4]
 IT Security Requirements [Section 5]
 TOE Summary Specification [Section 6]
The structure and content of this ST comply with the requirements specified in the Common
Criteria (CC), Part 1, Annex A, and Part 2.
1.1 ST and TOE Reference
This section provides information needed to identify and control this ST and its TOE.
Table 3 ST and TOE Identification
Name Description
ST Title Web Security Appliance Security Target
ST Version 1.0
Publication Date September 13, 2017
Vendor and ST Author Cisco Systems, Inc.
TOE Reference Web Security Appliance
TOE Hardware Models S690, S690X, S680, S670, S390, S380, S370, S190, S170, S100v, S300v
TOE Software Version AsyncOS 10.5
Keywords Web, Data Protection, Authentication, Network Device
1.2 TOE Overview
The Cisco Web Security Appliance TOE provides comprehensive web protection services for
web traffic. It is a web protection product that monitors HTTP/HTTPS network traffic, analyzes
the monitored network traffic using various techniques, and reacts to identified threats associated
with web traffic (such as blacklisted urls and inappropriate or malicious content). The TOE
includes the models as defined in Table 3 in section 1.1.
1.2.1 TOE Product Type
The TOE is a secure web gateway for securing and controlling web traffic. WSA is a protection
product that can block malware, and threats that may be delivered via web traffic. WSA receives
updates from the Cisco Talos Security Intelligence. Cisco Talos prevents zero-hour attacks by
continually generating new rules that feed updates to the Cisco WSA. The updates occur every 3
to 5 minutes keeping the WSA threat database updated for current web threats. WSA includes
Advanced Malware Protection (AMP) for enhanced malware protection.
Once a threat is detected through web traffic scanning, the TOE will take action based on
authorized administrator configurable filters.
8
The Cisco WSA is designed to serve as a secure web gateway, providing scanning of both
inbound and outbound traffic in real time for malware. All web traffic from HTML images to
Flash content is analyzed using security and context aware scanning engines.
Intelligent multi-scanning determines which scanning engine to use based on reputation and
content type, optimizing efficiency and catch rates. Traffic inspection engines analyze traffic in
real time, breaking it into functional elements and pushing those elements to the malware
engines best designed to inspect the specific type data. Specific features such as chat,
messaging, video, and audio can be allowed or blocked.
The TOE provides two management interfaces: Command Line Interface (CLI) and web-based
Graphical User Interface. The GUI contains most of the functionality to configure and monitor
the system. However, not all CLI commands are available in the GUI; some features are only
available through the CLI.
1.2.2 Supported non-TOE Hardware/ Software/ Firmware
The TOE supports (in some cases optionally) the following hardware, software, and firmware in
its environment when the TOE is configured in its evaluated configuration:
Table 4: IT Environment Components
Component Required TOE
Interface
Usage/Purpose Description for TOE performance
Certification
Authority
No Management
Port
This includes any IT Environment Management workstation with
a SSH client installed that is used by the TOE administrator to
support TOE administration through SSH protected channels.
Any SSH client that supports SSHv2 may be used.
Management
Workstation with
SSH Client
Yes Management
Port
This includes any IT Environment Management workstation with
a SSH client installed that is used by the TOE administrator to
support TOE administration through SSH protected channels.
Any SSH client that supports SSHv2 may be used.
Management
Workstation
using web
browser for
HTTPS
Yes Management
Port
This includes any IT Environment Management workstation with
a web browser installed that is used by the TOE administrator to
support TOE administration through HTTPS protected channels.
Any web browser that supports TLSv1.1 or above with the
supported ciphersuites may be used.
Local Console No Serial Console
Port
This includes any IT Environment Console that is directly
connected to the TOE via the Serial Console Port and is used by
the TOE administrator to support TOE administration.
NTP Server No Management
Port
The TOE supports communications with an NTP server in order
to synchronize the date and time on the TOE with the NTP
server’s date and time. A solution must be used that supports
secure communications with up to a 32 character key.
Web Server Yes 10/100/1000
Port
This includes the IT environment Web servers that the TOE
receives and sends HTTP/HTTPS.
Syslog Server Yes Management
Port
This includes any syslog server to which the TOE would transmit
syslog messages.
Update Server No Management
Port
This includes the Cisco IT environment update servers that are
used to download the latest software updates for the TOE.
9
1.3 TOE DESCRIPTION
This section provides an overview of the Cisco Web Security Appliance TOE. The TOE is a
security appliance that scans traffic between an external network and the customer’s internal
network. Traffic flowing to and from the external network to the internal network is first routed
through the TOE appliance.
Through the intercept, scanning, and reporting functions, the TOE can detect potentially
malicious data of various types and filter traffic for restricted content and malware.
The TOE analyzes the characteristics of web requests and responses and makes determinations
regarding whether the request or response will be blocked, monitored, or allowed. The TOE
provides two independent sets of security services to fulfill its objectives, Web Proxy Services
and the Layer 4 (L4) Traffic Monitor.
Web Proxy Services examine outbound client requests and consist of four features which work in
concert to prevent users from accessing known or suspected malware distribution vectors. The
four features of Web Proxy Services are:
 Policy Groups – administrator defined groups of users which specify exceptions to global
policy settings based on client IP address, authentication group, or username.
 Uniform Resource Locator (URL) Filters – control user access to URLs based on the
category of a particular HTTP request.
 Web Reputation Filters – analyze web server behavior and characteristics to identify
suspicious activity.
 Anti-Malware Scanning – when a URL has a questionable reputation, the HTTP traffic
receives an in-depth inspection using the Dynamic Vectoring and Streaming (DVS)
engine in concert with the Webroot Signature database.
The L4 Traffic Monitor detects rogue traffic by monitoring all network traffic received on all
Transmission Control Protocol (TCP) ports on the appliance and matching that traffic to an
internal database based on domain names and Internet Protocol (IP) addresses.
The following figure provides a visual depiction of an example TOE deployment. The TOE
boundary is surrounded with a hashed red line.
10
Figure 1 TOE Example Deployment
The previous figure includes the following:
 TOE
 The following are considered to be in the IT Environment:
o Management Workstation
o NTP Server
o Syslog Server
o Router/Switch
o Update Server
o Client Machines
o Firewall
1.4 TOE Evaluated Configuration
The TOE consists of one or more appliances as specified in section 1.5 below and includes the
Cisco AsyncOS software. The Cisco AsyncOS configuration determines how packets are
11
handled to and from the TOE’s network interfaces. In addition, the appliance configuration
determines how suspected malicious web traffic is handled.
The TOE can optionally connect to an NTP server on its internal network for time services. Also,
if the WSA is to be remotely administered, then the management station must be connected to an
internal network, SSHv2 must be used to remotely connect to the appliance. A syslog server is
also used to store audit records. If these servers are used, they must be attached to the internal
(trusted) network. The internal (trusted) network is meant to be separated effectively from
unauthorized individuals and user traffic; one that is in a controlled environment where
implementation of security policies can be enforced.
1.5 Physical Scope of the TOE
The TOE is comprised of both software and hardware. The hardware is comprised of the
following: S690, S690X, S680, S670, S390, S380, S370, S190, S170 running on Cisco UCS
servers (blade or rack-mounted). The software version of the TOE is Cisco AsyncOS version
10.5.
The Cisco Web Security Appliance that comprises the TOE has common hardware
characteristics. These characteristics affect only non-TSF relevant functions of the appliances
(such as throughput and amount of storage) and therefore support security equivalency of the
appliances in terms of hardware.
The S100v, S300v models running on Cisco UCS servers have similar disk layouts, queue and
cache sizes, and configurations as their dedicated hardware appliance counterparts. The software
images for the S100v, S300v have been pre-configured with disk space, queue/cache space,
memory, and processor cores. These differences in the pre-configurations of these models are
the reason the software images differ.
The TOE guidance documentation that is considered to be part of the TOE can be found listed in
the Cisco Web Security Appliance Common Criteria Operational User Guidance and Preparative
Procedures document and are downloadable from the http://cisco.com web site. The TOE is
comprised of the following specifications as described in Table 5 below:
Table 5 TOE Models and Specifications
Model Processor Memory Hard disk Interfaces/UCS Server
S690 Intel Xeon 64GB 4.8 TB (8 x 600 GB
SAS)
(2) USB Console Port
(1) Console Port (RJ-45
connector)
(1) Management Port
(4) 10/100/1000 Port
(2) Power Supply
(1) Remote Power Management
Port
S690X Intel Xeon 64GB 9.6 TB (16 x 600 GB
SAS)
(2) USB Console Port
(1) Console Port (RJ-45
connector)
(1) Management Port
(4) 10/100/1000 Port
12
Model Processor Memory Hard disk Interfaces/UCS Server
(2) Power Supply
(1) Remote Power Management
Port
S680 Intel Xeon 32 GB 2.4 TB (8 x 600 GB
SAS)
(2) USB Console Port
(1) Console Port (RJ-45
connector)
(1) Management Port
(4) 10/100/1000 Port
(2) Power Supply
(1) Remote Power Management
Port
S670 Intel Xeon 8 GB 2.7 TB (6 x 450 GB
SAS)
(2) USB Console Port
(1) Console Port (RJ-45
connector)
(1) Management Port
(4) 10/100/1000 Port
(2) Power Supply
(1) Remote Power Management
Port
S390 Intel Xeon 32 GB 2.4 TB
(4 x 600 GB SAS)
Console Port (RJ-45 connector)
(1) Management Port
(4) 10/100/1000 Port
(2) Power Supply
(1) Remote Power Management
Port
S380 Intel Xeon 16 GB 2.4 TB
(4 x 600 GB SAS)
(2) USB Console Port
(1) Console Port
(1) Management Port
(4) 10/100/1000 Port
(2) Power Supply
(1) Remote Power Management
Port
S370 Intel Xeon 4 GB 1.8 TB
(4 x 450 GB SAS)
(2) USB Console Port
(1) Console Port
(1) Management Port
(4) 10/100/1000 Port
(2) Power Supply
(1) Remote Power Management
Port
S190 Intel Xeon 8 GB 1.2 TB
(2 x 600 GB SAS)
(2) USB Console Port
(1) Console Port
(1) Management Port
(2) 10/100/1000 Port
(1) Power Supply
S170 Intel Xeon 4 GB 500 GB (2 x 250 GB
SATA)
(2) USB Console Port
(1) Console Port
(1) Management Port
(2) 10/100/1000 Port
(1) Power Supply
S100v UCS C-Series1
UCS C-Series UCS C-Series UCS C-Series
1
See the UCS C-Series data sheets for details on the interfaces
13
Model Processor Memory Hard disk Interfaces/UCS Server
running ESXi 5.5 running ESXi 5.5 running ESXi 5.5 running ESXi 5.5
S300v UCS C-Series
running ESXi 5.5
UCS C-Series
running ESXi 5.5
UCS C-Series
running ESXi 5.5
UCS C-Series
running ESXi 5.5
1.6 Logical Scope of the TOE
The TOE is comprised of several security features. Each of the security features identified above
consists of several security functionalities, as identified below.
1. Security Audit
2. Cryptographic Support
3. Identification and Authentication
4. Security Management
5. Protection of the TSF
6. TOE Access
7. Trusted Path/Channels
These features are described in more detail in the subsections below. In addition, the TOE
implements all RFCs of the NDcPP v1.0 as necessary to satisfy testing/assurance measures
prescribed therein.
1.6.1 Security Audit
The Cisco Web Security Appliance provides extensive auditing capabilities. The TOE can audit
events related to cryptographic functionality, identification and authentication, and
administrative actions. The Cisco Web Security Appliance generates an audit record for each
auditable event. Each security relevant audit event has the date, timestamp, event description,
and subject identity. The administrator configures auditable events, performs back-up
operations, and manages audit data storage. The TOE provides the administrator with a circular
audit trail or a configurable audit trail threshold to track the storage capacity of the audit trail.
Audit logs are backed up over an encrypted channel to an external audit server.
1.6.2 Cryptographic Support
The TOE provides cryptography in support of other Cisco WSA security functionality. The
entropy source provides 256 bits of entropy used to seed the RNG. After cryptographic keys are
used, they are zeroized. The cryptographic algorithms are provided by CiscoSSL FIPS Object
Module 6.0.
Table 6 CAVP References
Algorithm Cert. # SFR
AES 4561, 4680 FCS_SSHC_EXT.1
FCS_SSHS_EXT.1
FCS_TLSS_EXT.1
FCS_HTTPS_EXT.1
FCS_COP.1.1(1)
HMAC 3013, 3096 FCS_SSHC_EXT.1
FCS_SSHS_EXT.1
FCS_TLSS_EXT.1
FCS_HTTPS_EXT.1
FCS_COP.1.1(4)
DRBG 1509, 1583 FCS_SSHC_EXT.1
FCS_SSHS_EXT.1
15
Algorithm Cert. # SFR
FCS_TLSS_EXT.1
FCS_HTTPS_EXT.1
FCS_RBG_EXT.1
ECDSA 1113, 1155 FCS_TLSS_EXT.1
FCS_HTTPS_EXT.1
FCS_CKM.1
FCS_CKM.2
RSA 2488, 2553 FCS_SSHC_EXT.1
FCS_SSHS_EXT.1
FCS_TLSS_EXT.1
FCS_HTTPS_EXT.1
FCS_CKM.1
FCS_CKM.2
FCS_COP.1.1(2)
SHA 3739, 3831 FCS_SSHC_EXT.1
FCS_SSHS_EXT.1
FCS_TLSS_EXT.1
FCS_HTTPS_EXT.1
FCS_COP.1.1(3)
CVL 1244, 1325 FCS_SSHC_EXT.1
FCS_SSHS_EXT.1
FCS_TLSS_EXT.1
FCS_CKM.2
The DH related certificates apply to the key derivation function used in TLS and SSH.
The TOE provides cryptography in support of remote administrative management via SSHv2.
The cryptographic services provided by the TOE are described in Table 7 below.
Table 7 TOE Provided Cryptography
Cryptographic Method Use within the TOE
Secure Shell Establishment (SSH) Used to establish initial SSH session.
Transport Layer Security (TLS) Used in TLS session establishment.
AES Used to encrypt TLS session traffic.
Used to encrypt SSH session traffic.
ECDH Used to provide key exchange in SSH
RSA Signature Services Used in TLS session establishment.
Used in SSH session establishment.
X.509 certificate signing
HMAC Used for keyed hash, integrity services in TLS an SSH session
establishment.
DRBG Used for random number generation
Used in TLS session establishment.
Used in SSH session establishment.
SHA Used to provide TLS traffic integrity verification
The following SFRs are supported by the Cryptographic Module:
16
 FCS_CKM.1
 FCS_CKM.2
 FCS_CKM.4
 FCS_COP.1 including all iterations
 FCS_HTTPS_EXT.1
 FCS_SSHS_EXT.1
 FCS_TLSS_EXT.1
1.6.3 Identification and authentication
The TOE performs user authentication for the Authorized Administrator of the TOE. The TOE
provides authentication services for administrative users wishing to connect to the TOE’s secure
CLI and GUI administrative interfaces. Prior to an administrator logging in, a login banner is
presented at both the CLI and GUI. The TOE requires Authorized Administrators to authenticate
prior to being granted access to any of the management functionality.
The TOE can be configured to require a minimum password length of 15 characters as well as
mandatory password complexity rules that includes special characters. The TOE provides
administrator authentication against a local user database. Password-based authentication can be
performed on the serial console or remote interfaces. The SSHv2 interface also supports
authentication using SSH keys. The remote GUI is protected using TLS.
1.6.4 Security Management
The TOE provides secure administrative services for management of general TOE configuration
and the security functionality provided by the TOE. All TOE administration occurs either
through a secure SSHv2 session or via a local console connection. The TOE provides the ability
to securely manage:
 All TOE administrative users;
 All identification and authentication;
 All audit functionality of the TOE;
 All TOE cryptographic functionality;
 The timestamps maintained by the TOE;
 Updates to the TOE; and
 TOE configuration file storage and retrieval.
The TOE provides capabilities to manage its security functions, and controls access to those
capabilities through the use of administrative roles with varying security management
authorizations.
Administrators can create configurable login banners to be displayed at time of login, and can
also define an inactivity timeout for each admin interface to terminate sessions after a set period
of inactivity.
17
1.6.5 Protection of the TSF
The TOE protects against interference and tampering by untrusted subjects by implementing
identification, authentication, and access controls to limit configuration to Authorized
Administrators. The TOE prevents reading of cryptographic keys and passwords.
The TOE internally maintains the date and time. This date and time is used as the timestamp that
is applied to audit records generated by the TOE. Administrators can update the TOE’s clock
manually, or can optionally configure the TOE to use NTP to synchronize the TOE’s clock with
an external time source. Finally, the TOE performs testing to verify correct operation of the
appliance itself and that of the cryptographic module.
The TOE is able to verify any software updates prior to the software updates being installed on
the TOE to avoid the installation of unauthorized software.
1.6.6 TOE Access
The TOE is able to download software updates from the Update Server. The TOE can terminate
inactive sessions after an Authorized Administrator configurable time-period. Once a session
has been terminated the TOE requires the user to re-authenticate to establish a new session.
The TOE can also display an Authorized Administrator specified banner on the CLI and GUI
management interfaces prior to allowing any administrative access to the TOE. Administrators
are able to exit their own administrator sessions.
1.6.7 Trusted path/Channels
The TOE allows trusted paths to be established to itself from remote administrators over SSHv2
for remote CLI access and HTTPS for remote GUI access. The TOE can push log files to an
external syslog server using SCP over SSH.
1.7 Excluded Functionality
The following functionality is excluded from the evaluated configuration.
Table 8 Excluded Functionality
Excluded Functionality Exclusion Rationale
Non-FIPS 140-2 mode of operation This mode of operation includes non-FIPS allowed
operations.
These services will be disabled by configuration. The exclusion of this functionality does not
affect compliance to the collaborative Protection Profile for Network Devices Version 1.0.
18
Please note that the functionality evaluated is scoped exclusively to the security functional
requirements specified in the Section 5 of this document. The web protection services
functionality included in the product and described in Section 1.2 and 1.3 were not assessed as
part of this evaluation. All other functionality provided by the devices needs to be assessed
separately and no further conclusions can be drawn about their effectiveness.
19
2 CONFORMANCE CLAIMS
2.1 Common Criteria Conformance Claim
The TOE and ST are compliant with the Common Criteria (CC) Version 3.1, Revision 4, dated:
September 2012. For a listing of Assurance Requirements claimed see section 5.5.
The TOE and ST are CC Part 2 extended and CC Part 3 conformant.
2.2 Protection Profile Conformance
The TOE and ST are conformant with the Protection Profiles as listed in Table 9 below:
Table 9 Protection Profiles
Protection Profile Version Date
collaborative Protection Profile for Network Devices (NDcPP) 1.0 27-Feb-2015
2.3 Protection Profile Conformance Claim Rationale
2.3.1 TOE Appropriateness
The TOE provides all of the functionality at a level of security commensurate with that identified
in the U.S. Government Protection Profile:
 collaborative Protection Profile for Network Devices, Version 1.0
2.3.2 TOE Security Problem Definition Consistency
The Assumptions, Threats, and Organizational Security Policies included in the Security Target
represent the Assumptions, Threats, and Organizational Security Policies specified in the
collaborative Protection Profile for Network Devices Version 1.0 for which conformance is
claimed verbatim. All concepts covered in the Protection Profile Security Problem Definition
are included in the Security Target Statement of Security Objectives Consistency.
The Security Objectives included in the Security Target represent the Security Objectives
specified in the NDcPPv1.0 for which conformance is claimed verbatim. All concepts covered
in the Protection Profile’s Statement of Security Objectives are included in the Security Target.
2.3.3 Statement of Security Requirements Consistency
The Security Functional Requirements included in the Security Target represent the Security
Functional Requirements specified in the NDcPPv1.0 for which conformance is claimed
verbatim. All concepts covered in the Protection Profile’s Statement of Security Requirements
are included in this Security Target. Additionally, the Security Assurance Requirements
included in this Security Target are identical to the Security Assurance Requirements included in
section 4.3 of the NDcPPv1.0.
20
3 SECURITY PROBLEM DEFINITION
This chapter identifies the following:
 Significant assumptions about the TOE’s operational environment.
 IT related threats to the organization countered by the TOE.
 Environmental threats requiring controls to provide sufficient protection.
 Organizational security policies for the TOE as appropriate.
This document identifies assumptions as A.assumption with “assumption” specifying a unique
name. Threats are identified as T.threat with “threat” specifying a unique name. Organizational
Security Policies (OSPs) are identified as P.osp with “osp” specifying a unique name.
3.1 Assumptions
The specific conditions listed in the following subsections are assumed to exist in the TOE’s
environment. These assumptions include both practical realities in the development of the TOE
security requirements and the essential environmental conditions on the use of the TOE.
Table 10 TOE Assumptions
Assumption Assumption Definition
A.PHYSICAL_PROTECTION The network device is assumed to be physically protected in its
operational environment and not subject to physical attacks that
compromise the security and/or interfere with the device’s physical
interconnections and correct operation. This protection is assumed to
be sufficient to protect the device and the data it contains. As a result,
the cPP will not include any requirements on physical tamper
protection or other physical attack mitigations. The cPP will not expect
the product to defend against physical access to the device that allows
unauthorized entities to extract data, bypass other controls, or otherwise
manipulate the device.
A.LIMITED_FUNCTIONALITY The device is assumed to provide networking functionality as its core
function and not provide functionality/ services that could be deemed
as general purpose computing. For example the device should not
provide computing platform for general purpose applications (unrelated
to networking functionality).
A.NO_THRU_TRAFFIC_PROTECTION A standard/generic network device does not provide any assurance
regarding the protection of traffic that traverses it. The intent is for the
network device to protect data that originates on or is destined to the
device itself, to include administrative data and audit data. Traffic
that is traversing the network device, destined for another network
entity, is not covered by the ND cPP. It is assumed that this protection
will be covered by cPPs for particular types of network devices (e.g,
firewall).
A.TRUSTED_ADMINISTRATOR The Security Administrator(s) for the network device are assumed to be
trusted and to act in the best interest of security for the organization.
This includes being appropriately trained, following policy, and
adhering to guidance documentation. Administrators are trusted to
ensure passwords/credentials have sufficient strength and entropy and
to lack malicious intent when administering the device. The network
device is not expected to be capable of defending against a malicious
21
Assumption Assumption Definition
administrator that actively works to bypass or compromise the
security of the device.
A.REGULAR_UPDATES The network device firmware and software is assumed to be updated by
an administrator on a regular basis in response to the release of product
updates due to known vulnerabilities.
A.ADMIN_CREDENTIALS_SECURE The administrator’s credentials (private key) used to access the network
device are protected by the platform on which they reside.
3.2 Threats
The following table lists the threats addressed by the TOE and the IT Environment. The
assumed level of expertise of the attacker for all the threats identified below is Enhanced-Basic.
Table 11 Threats
Threat Threat Definition
T.UNAUTHORIZED_ADMINISTRATOR_ACCESS Threat agents may attempt to gain administrator access to
the network device by nefarious means such as
masquerading as an administrator to the device,
masquerading as the device to an administrator, replaying
an administrative session (in its entirety, or selected
portions), or performing man-in-the-middle attacks, which
would provide access to the administrative session, or
sessions between network devices. Successfully gaining
administrator access allows malicious actions that
compromise the security functionality of the device and the
network on which it resides.
T.WEAK_CRYPTOGRAPHY Threat agents may exploit weak cryptographic algorithms
or perform a cryptographic exhaust against the key space.
Poorly chosen encryption algorithms, modes, and key sizes
will allow attackers to compromise the algorithms, or brute
force exhaust the key space and give them unauthorized
access allowing them to read, manipulate and/or control the
traffic with minimal effort.
T.UNTRUSTED_COMMUNICATION_CHANNELS Threat agents may attempt to target network devices that
do not use standardized secure tunneling protocols to
protect the critical network traffic. Attackers may take
advantage of poorly designed protocols or poor key
management to successfully perform man-in-themiddle
attacks, replay attacks, etc. Successful attacks will result in
loss of confidentiality and integrity of the critical network
traffic, and potentially could lead to a compromise of the
network device itself.
22
Threat Threat Definition
T.WEAK_AUTHENTICATION_ENDPOINTS Threat agents may take advantage of secure protocols that
use weak methods to authenticate the endpoints – e.g.,
shared password that is guessable or transported as
plaintext. The consequences are the same as a poorly
designed protocol, the attacker could masquerade as the
administrator or another device, and the attacker could
insert themselves into the network stream and perform a
man-in-the-middle attack. The result is the critical network
traffic is exposed and there could be a loss of
confidentiality and integrity, and potentially the network
device itself could be compromised.
T.UPDATE_COMPROMISE Threat agents may attempt to provide a compromised
update of the software or firmware which undermines the
security functionality of the device. Non-validated updates
or updates validated using non-secure or weak
cryptography leave the update firmware vulnerable to
surreptitious alteration.
T.UNDETECTED_ACTIVITY Threat agents may attempt to access, change, and/or
modify the security functionality of the network device
without administrator awareness. This could result in the
attacker finding an avenue (e.g., misconfiguration, flaw in
the product) to compromise the device and the
administrator would have no knowledge that the device has
been compromised.
T.SECURITY_FUNCTIONALITY_COMPROMISE Threat agents may compromise credentials and device data
enabling continued access to the network device and its
critical data. The compromise of credentials include
replacing existing credentials with an attacker’s
credentials, modifying existing credentials, or obtaining the
administrator or device credentials for use by the attacker.
T.PASSWORD_CRACKING Threat agents may be able to take advantage of weak
administrative passwords to gain privileged access to the
device. Having privileged access to the device provides the
attacker unfettered access to the network traffic, and may
allow them to take advantage of any trust
relationships with other network devices.
T.SECURITY_FUNCTIONALITY_FAILURE A component of the network device may fail during start-
up or during operations causing a compromise or failure in
the security functionality of the network device, leaving the
device susceptible to attackers.
3.3 Organizational Security Policies
The following table lists the Organizational Security Policies imposed by an organization to address its security
needs.
Table 12 Organizational Security Policies
Policy Name Policy Definition
P.ACCESS_BANNER The TOE shall display an initial banner describing restrictions of use, legal agreements, or
any other appropriate information to which users consent by accessing the TOE.
23
24
4 SECURITY OBJECTIVES
This Chapter identifies the security objectives of the TOE and the IT Environment. The security
objectives identify the responsibilities of the TOE and the TOE’s IT environment in meeting the
security needs.
 This document identifies objectives of the TOE as O.objective with objective specifying
a unique name. Objectives that apply to the IT environment are designated as
OE.objective with objective specifying a unique name.
4.1 Security Objectives for the TOE
The collaborative Protection Profile for Network Devices v1.0 does not define any security
objectives for the TOE.
4.2 Security Objectives for the Environment
All of the assumptions stated in section 3.1 are considered to be security objectives for the
environment. The following are the Protection Profile non-IT security objectives, which, in
addition to those assumptions, are to be satisfied without imposing technical requirements on the
TOE. That is, they will not require the implementation of functions in the TOE hardware and/or
software. Thus, they will be satisfied largely through application of procedural or administrative
measures.
Table 13 Security Objectives for the Environment
Environment Security Objective IT Environment Security Objective Definition
OE.PHYSICAL Physical security, commensurate with the value of the TOE and the
data it contains, is provided by the environment.
OE.NO_GENERAL_PURPOSE There are no general-purpose computing capabilities (e.g., compilers
or user applications) available on the TOE, other than those services
necessary for the operation, administration and support of the TOE.
OE.NO_THRU_TRAFFIC_PROTECTION The TOE does not provide any protection of traffic that traverses it.
It is assumed that protection of this traffic will be covered by other
security and assurance measures in the operational environment.
OE.TRUSTED_ADMIN TOE Administrators are trusted to follow and apply all administrator
guidance in a trusted manner.
OE.UPDATES The TOE firmware and software is updated by an administrator on a
regular basis in response to the release of product updates due to
known vulnerabilities.
OE.ADMIN_CREDENTIALS_SECURE The administrator’s credentials (private key) used to access the TOE
must be protected on any other platform on which they reside.
25
5 SECURITY REQUIREMENTS
This section identifies the Security Functional Requirements for the TOE. The Security
Functional Requirements included in this section are derived from Part 2 of the Common Criteria
for Information Technology Security Evaluation, Version 3.1, Revision 4, dated: September 2012
and all international interpretations.
5.1 Conventions
The CC defines operations on Security Functional Requirements: assignments, selections,
assignments within selections and refinements. This document uses the following font
conventions to identify the operations defined by the CC:
 Assignment: Indicated with italicized text;
 Refinement: Indicated with bold text;
 Selection: Indicated with underlined text;
 Iteration: Indicated by appending the iteration number in parenthesis, e.g., (1), (2), (3).
Explicitly stated SFRs are identified by having a label ‘EXT’ after the requirement name for
TOE SFRs. Formatting conventions outside of operations and iterations matches the formatting
specified within the NDcPP.
5.2 TOE Security Functional Requirements
This section identifies the Security Functional Requirements for the TOE. The TOE Security
Functional Requirements that appear in the following table are described in more detail in the
following subsections.
Table 14 Security Functional Requirements
Class Name Component Identification Component Name
FAU: Security audit FAU_GEN.1 Audit data generation
FAU_GEN.2 User Identity Association
FAU_STG_EXT.1 Protected Audit Event Storage
FCS: Cryptographic
support
FCS_CKM.1 Cryptographic Key Generation (Refined)
FCS_CKM.2 Cryptographic Key Establishment (Refined)
FCS_CKM.4 Cryptographic Key Destruction
FCS_COP.1(1) Cryptographic Operation (for data encryption/decryption)
FCS_COP.1(2) Cryptographic Operation (for cryptographic signature)
FCS_COP.1(3) Cryptographic Operation (for cryptographic hashing)
FCS_COP.1(4) Cryptographic Operation (for keyed-hash message
authentication)
FCS_HTTPS_EXT.1 HTTPS
FCS_RBG_EXT.1 Cryptographic Operation (Random Bit Generation)
FCS_SSHC_EXT.1 SSH Client Protocol
FCS_SSHS_EXT.1 SSH Server Protocol
FCS_TLSS_EXT.1 TLS Server Protocol
FIA: Identification and
authentication
FIA_PMG_EXT.1 Password Management
FIA_UIA_EXT.1 User Identification and Authentication
FIA_UAU_EXT.2 Password-based Authentication Mechanism
FIA_UAU.7 Protected Authentication Feedback
FIA_X509_EXT.1 X.509 Certificate Validation
26
Class Name Component Identification Component Name
FIA_X509_EXT.2 X.509 Certificate Authentication
FIA_X509_EXT.3 X.509 Certificate Requests
FMT: Security
management
FMT_MOF.1(1) )
/TrustedUpdate
TrustedUpdate Management of security functions
behaviour
FMT_MTD.1 Management of TSF Data
FMT_SMF.1 Specification of Management Functions
FMT_SMR.2 Restrictions on Security Roles
FPT: Protection of the
TSF
FPT_SKP_EXT.1 Protection of TSF Data (for reading of all symmetric keys)
FPT_APW_EXT.1 Protection of Administrator Passwords
FPT_STM.1 Reliable Time Stamps
FPT_TST_EXT.1 TSF Testing (Extended)
FPT_TUD_EXT.1 Trusted Update
FTA: TOE Access FTA_SSL_EXT.1 TSF-initiated Session Locking
FTA_SSL.3 TSF-initiated Termination
FTA_SSL.4 User-initiated Termination
FTA_TAB.1 Default TOE Access Banners
FTP: Trusted
Path/Channels
FTP_ITC.1 Inter-TSF trusted channel
FTP_TRP.1 Trusted Path
5.3 SFRs Drawn from NDcPP ONLY
5.3.1 Security audit (FAU)
5.3.1.1 FAU_GEN.1 Audit data generation
FAU_GEN.1.1 The TSF shall be able to generate an audit record of the following auditable
events:
a) Start-up and shutdown of the audit functions;
b) All auditable events for the not specified level of audit; and
c) All administrative actions comprising:
 Administrative login and logout (name of user account shall be logged if individual user
accounts are required for administrators).
 Security related configuration changes (in addition to the information that a change
occurred it shall be logged what has been changed).
 Generating/import of, changing, or deleting of cryptographic keys (in addition to the
action itself a unique key name or key reference shall be logged).
 Resetting passwords (name of related user account shall be logged).
 Starting and stopping services (if applicable)
 no other actions;
d) Specifically defined auditable events listed in Table 15.
FAU_GEN.1.2 The TSF shall record within each audit record at least the following information:
a) Date and time of the event, type of event, subject identity, and the outcome (success or
failure) of the event; and
b) For each audit event type, based on the auditable event definitions of the functional
components included in the PP/ST, information specified in column three of Table 15.
27
Table 15 Auditable Events
SFR Auditable Event Additional Audit Record Contents
Audit Events and Details from NDcPP
FAU_GEN.1 None. None.
FAU_GEN.2 None. None.
FAU_STG_EXT.1 None. None.
FCS_CKM.1 None. None.
FCS_CKM.2 None. None.
FCS_CKM.4 None. None.
FCS_COP.1(1) None. None.
FCS_COP.1(2) None. None.
FCS_COP.1(3) None. None.
FCS_COP.1(4) None. None.
FCS_HTTPS_EXT.1 Failure to establish an HTTPS session. Reason for failure.
FCS_RBG_EXT.1 None. None.
FCS_SSHC_EXT.1 Failure to establish an SSH session Reason for failure.
Successful SSH rekey Non-TOE endpoint of connection (IP
address) for both successes and failures.
FCS_SSHS_EXT.1 Failure to establish an SSH session Reason for failure.
Successful SSH rekey Non-TOE endpoint of connection (IP
address) for both successes and failures.
FCS_TLSS_EXT.1 Failure to establish an TLS session Reason for failure.
FIA_PMG_EXT.1 None. None.
FIA_UIA_EXT.1 All use of the identification and
authentication mechanism.
Provided user identity, origin of the attempt
(e.g., IP address).
FIA_UAU_EXT.2 All use of the authentication
mechanism.
Origin of the attempt (e.g., IP address).
FIA_UAU.7 None. None.
FIA_X509_EXT.1 Unsuccessful attempt to validate a
certificate
Reason for failure
FIA_X509_EXT.2 None. None.
FIA_X509_EXT.3 None. None.
FMT_MOF.1(1)/Trusted
Update
Any attempt to initiate a manual update None.
FMT_MTD.1 All management activities of TSF data None.
FMT_SMF.1 None. None.
FMT_SMR.2 None. None.
FPT_SKP_EXT.1 None. None.
FPT_APW_EXT.1 None. None.
FPT_STM.1 Changes to the time. The old and new values for the time.
Origin of the attempt (e.g., IP address).
FPT_TST_EXT.1 None. None.
FPT_TUD_EXT.1 Initiation of update; result of the update
attempt (success and failure)
No additional information.
FTA_SSL_EXT.1 Any attempts at unlocking of an
interactive session.
None.
FTA_SSL.3 The termination of a remote session by
the session locking mechanism.
None.
FTA_SSL.4 The termination of an interactive
session.
None.
FTA_TAB.1 None. None.
FTP_ITC.1 Initiation of the trusted channel. Identification of the initiator and target of
28
SFR Auditable Event Additional Audit Record Contents
Termination of the trusted channel.
Failure of the trusted channel functions.
failed trusted channels establishment attempt.
FTP_TRP.1 Initiation of the trusted path.
Termination of the trusted path.
Failures of the trusted path functions.
Identification of the claimed user identity.
5.3.1.2 FAU_GEN.2 User Identity Association
FAU_GEN.2.1 For audit events resulting from actions of identified users, the TSF shall be able
to associate each auditable event with the identity of the user that caused the event.
5.3.1.3 FAU_STG_EXT.1 Protected Audit Event Storage
FAU_STG_EXT.1.1 The TSF shall be able to transmit the generated audit data to an
external IT entity using a trusted channel according to FTP_ITC.1.
FAU_STG_EXT.1.2 The TSF shall be able to store generated audit data on the TOE itself.
FAU_STG_EXT.1.3 The TSF shall [overwrite previous audit records according to the following
rule: when allotted space has reached its threshold, no other action] when the local storage space
for audit data is full.
5.3.2 Cryptographic Support (FCS)
5.3.2.1 FCS_CKM.1 Cryptographic Key Generation (Refined)
FCS_CKM.1.1 Refinement: The TSF shall generate asymmetric cryptographic keys in
accordance with a specified cryptographic key generation algorithm: [
 RSA schemes using cryptographic key sizes of 2048-bit or greater that meet the
following: FIPS PUB 186-4, “Digital Signature Standard (DSS)”, Appendix B.3;
 ECC schemes using “NIST curves” P-256, P-384, P-521 that meet the following:
FIPS PUB 186-4, “Digital Signature Standard (DSS)”, Appendix B.4;
] and specified cryptographic key sizes [assignment: cryptographic key sizes] that meet
the following: [assignment: list of standards].
5.3.2.2 FCS_CKM.2 Cryptographic Key Establishment (Refined)
FCS_CKM.2.1 The TSF shall perform cryptographic key establishment in accordance with
a specified cryptographic key establishment method: [
 RSA-based key establishment schemes that meets the following: NIST Special
Publication 800-56B, “Recommendation for Pair-Wise Key Establishment Schemes
Using Integer Factorization Cryptography”;
29
 Elliptic curve-based key establishment schemes that meets the following: NIST
Special Publication 800-56A, “Recommendation for Pair-Wise Key Establishment
Schemes Using Discrete Logarithm Cryptography”;
]
] that meets the following: [assignment: list of standards].
5.3.2.3 FCS_CKM.4 Cryptographic Key Destruction
FCS_CKM.4.1 The TSF shall destroy cryptographic keys in accordance with a specified
cryptographic key destruction method
For plaintext keys in volatile storage, the destruction shall be executed by a [single overwrite
consisting of [zeroes]];
• For plaintext keys in non-volatile storage, the destruction shall be executed by the invocation of
an interface provided by a part of the TSF that [
o logically addresses the storage location of the key and performs a [single-pass] overwrite
consisting of [zeroes];
]
that meets the following: No Standard.2
5.3.2.4 FCS_COP.1(1) Cryptographic Operation (for data encryption/decryption)
FCS_COP.1.1(1) Refinement: The TSF shall perform encryption/decryption in accordance with
a specified cryptographic algorithm AES used in [CBC] mode and cryptographic key sizes [128
bits, 256-bits] that met the following: AES as specified in ISO 18033-3, [CBC as specified in ISO
10116].
5.3.2.5 FCS_COP.1(2) Cryptographic Operation (for cryptographic signature)
FCS_COP.1.1(2) Refinement: The TSF shall perform cryptographic signature services
(generation and verification) in accordance with a specified cryptographic algorithm
 RSA Digital Signature Algorithm and cryptographic key sizes (modulus) [2048 bits
or greater]
that meets the following:
 [For RSA schemes: FIPS PUB 186-4, “Digital Signature Standard (DSS)”, Section
5.5, using PKCS #1 v2.1 Signature Schemes RSASSA-PSS and/or
RSASSAPKCS1v1_5; ISO/IEC 9796-2, Digital signature scheme 2 or Digital
Signature scheme 3] 3
5.3.2.6 FCS_COP.1(3) Cryptographic Operation (for cryptographic hashing)
FCS_COP.1.1(3) Refinement: The TSF shall perform cryptographic hashing services in
2
TD0130
3
TD0116
30
accordance with a specified cryptographic algorithm [SHA-1, SHA-256, SHA-384, SHA-512]
and cryptographic key sizes [assignment: cryptographic key sizes] that meet the following:
ISO/IEC 10118-3:2004.
5.3.2.7 FCS_COP.1(4) Cryptographic Operation (for keyed-hash message authentication)
FCS_COP.1.1(4) Refinement: The TSF shall perform keyed-hash message authentication in
accordance with a specified cryptographic algorithm [HMAC-SHA-1] and cryptographic key
sizes [160 (in bits) used in HMAC] and message digest sizes [160] bits that meet the following:
ISO/IEC 9797-2:2011, Section 7 “MAC Algorithm 2”.
5.3.2.8 FCS_HTTPS_EXT.1 Explicit: HTTPS
FCS_HTTPS_EXT.1.1 The TSF shall implement the HTTPS protocol that complies with RFC
2818.
FCS_HTTPS_EXT.1.2 The TSF shall implement HTTPS using TLS in accordance with
[FCS_TLSS_EXT.1].
FCS_HTTPS_EXT.1.3 The TSF shall establish the connection only if [the peer initiates
handshake].4
5.3.2.9 FCS_RBG_EXT.1 Extended: Cryptographic Operation (Random Bit Generation)
FCS_RBG_EXT.1.1 The TSF shall perform all random bit generation (RBG) services in
accordance with ISO/IEC 18031:2011 using [Hash_DRBG (any), HMAC_DRBG
(any), CTR_DRBG (AES)].
FCS_RBG_EXT.1.2 The deterministic RBG shall be seeded by at least one entropy source
that accumulates entropy from [1 software-based noise source] with minimum of [256 bits] of
entropy at least equal to the greatest security strength, according to ISO/IEC 18031:2011 Table
C.1 “Security Strength Table for Hash Functions”, of the keys and hashes that it will generate.
5.3.2.10 FCS_SSHC_EXT.1 Explicit: SSH
FCS_SSHC_EXT.1.1 The TSF shall implement the SSH protocol that complies with RFCs
4251, 4252, 4253, 4254, and [no other RFCs].
FCS_SSHC_EXT.1.2 The TSF shall ensure that the SSH protocol implementation supports the
following authentication methods as described in RFC 4252: public key-based, [no other
method].
FCS_SSHC_EXT.1.3 The TSF shall ensure that, as described in RFC 4253, packets greater than
[35,000] bytes in an SSH transport connection are dropped.
4
TD0125
31
FCS_SSHC_EXT.1.4 The TSF shall ensure that the SSH transport implementation uses the
following encryption algorithms and rejects all other encryption algorithms: aes128-cbc, aes256-
cbc, [no other algorithms].
FCS_SSHC_EXT.1.5 The TSF shall ensure that the SSH transport implementation uses [ssh-
rsa] and [no other public key algorithms] as its public key algorithm(s) and rejects all other
public key algorithms.
FCS_SSHC_EXT.1.6 The TSF shall ensure that the SSH transport implementation uses
[hmac-sha1] and [no other MAC algorithms] as its data integrity MAC algorithm(s) and rejects
all other MAC algorithm(s).
FCS_SSHC_EXT.1.7 The TSF shall ensure that [diffie-hellman-group14-sha1] and [no other
methods] are the only allowed key exchange methods used for the SSH protocol.
FCS_SSHC_EXT.1.8 The TSF shall ensure that within SSH connections the same session keys
are used for a threshold of no longer than one hour, and no more than one gigabyte of transmitted
data. After either of the thresholds are reached a rekey needs to be performed.
FCS_SSHC_EXT.1.9 The TSF shall ensure that the SSH client authenticates the identity of
the SSH server using a local database associating each host name with its corresponding
public key or [no other methods] as described in RFC 4251 section 4.1.
5.3.2.11 FCS_SSHS_EXT.1 SSH Server Protocol
FCS_SSHS_EXT.1.1 The TSF shall implement the SSH protocol that complies with RFCs
4251, 4252, 4253, 4254, and [no other RFCs].
FCS_SSHS_EXT.1.2 The TSF shall ensure that the SSH protocol implementation supports the
following authentication methods as described in RFC 4252: public key-based, [password-
based].
FCS_SSHS_EXT.1.3 The TSF shall ensure that, as described in RFC 4253, packets greater than
[35,000] bytes in an SSH transport connection are dropped.
FCS_SSHS_EXT.1.4 The TSF shall ensure that the SSH transport implementation uses the
following encryption algorithms: aes128-cbc, aes256-cbc, [no other algorithms].
FCS_SSHS_EXT.1.5 The TSF shall ensure that the SSH transport implementation uses [ssh-rsa]
and [no other methods] as its public key algorithm(s) and rejects all other public key algorithms.
FCS_SSHS_EXT.1.6 The TSF shall ensure that the SSH transport implementation uses
[hmac-sha1] and [no other MAC algorithms] as its data integrity MAC algorithm(s) and rejects
all other MAC algorithm(s).
32
FCS_SSHS_EXT.1.7 The TSF shall ensure that [diffie-hellman-group14-sha1] and [no other
methods] are the only allowed key exchange methods used for the SSH protocol.
FCS_SSHS_EXT.1.8 The TSF shall ensure that within SSH connections the same session keys
are used for a threshold of no longer than one hour, and no more than one gigabyte of transmitted
data. After either of the thresholds are reached a rekey needs to be performed.
5.3.2.12 FCS_TLSS_EXT.1 TLS Server Protocol
FCS_TLSS_EXT.1.1 The TSF shall implement [TLS 1.2 (RFC 5246), TLS 1.1
(RFC 4346)] supporting the following ciphersuites:
 Mandatory Ciphersuites:
o TLS_RSA_WITH_AES_128_CBC_SHA as defined in RFC 3268
 [Optional Ciphersuites:
o TLS_RSA_WITH_AES_256_CBC_SHA as defined in RFC 3268
o TLS_RSA_WITH_AES_128_CBC_SHA256 as defined in RFC 5246
o TLS_RSA_WITH_AES_256_CBC_ SHA256 as defined in RFC 5246
o TLS_ECDHE_RSA_WITH_AES_128_CBC_SHA as defined in RFC 4492
o TLS_ECDHE_RSA_WITH_AES_256_CBC_SHA as defined in RFC 4492
o TLS_ECDHE_RSA_WITH_AES_256_GCM_SHA384 as defined in RFC 5289
o TLS_ECDHE_RSA_WITH_AES_128_GCM_SHA256 as defined in RFC 5289
o no other ciphersuite].
FCS_TLSS_EXT.1.2 The TSF shall deny connections from clients requesting SSL 2.0, SSL 3.0,
TLS 1.0, and [none].
FCS_TLSS_EXT.1.3 The TSF shall generate key establishment parameters using RSA with
key size 2048 bits and [no other size] and [no other].
5.3.3 Identification and authentication (FIA)
5.3.3.1 FIA_PMG_EXT.1 Password Management
FIA_PMG_EXT.1.1 The TSF shall provide the following password management capabilities
for administrative passwords:
1. Passwords shall be able to be composed of any combination of upper and lower case
letters, numbers, and the following special characters: [“!”, “@”, “#”, “$”, “%”, “^”,
“&”, “*”, “(”, “)”;
2. Minimum password length shall settable by the Security Administrator, and support
passwords of 15 characters or greater;
33
5.3.3.2 FIA_UIA_EXT.1 User Identification and Authentication
FIA_UIA_EXT.1.1 The TSF shall allow the following actions prior to requiring the non-TOE
entity to initiate the identification and authentication process:
 Display the warning banner in accordance with FTA_TAB.1;
 [no other actions.]
FIA_UIA_EXT.1.2 The TSF shall require each administrative user to be successfully
identified and authenticated before allowing any other TSF-mediated action on behalf of that
administrative user.
5.3.3.3 FIA_UAU_EXT.2 Extended: Password-based Authentication Mechanism
FIA_UAU_EXT.2.1 The TSF shall provide a local password-based authentication mechanism,
[public key] to perform administrative user authentication.
5.3.3.4 FIA_UAU.7 Protected Authentication Feedback
FIA_UAU.7.1 The TSF shall provide only obscured feedback to the administrative user while
the authentication is in progress at the local console.
5.3.3.5 FIA_X509_EXT.1 X.509 Certificate Validation
FIA_X509_EXT.1.1 The TSF shall validate certificates in accordance with the following
rules:
 RFC 5280 certificate validation and certificate path validation.
 The certificate path must terminate with a trusted CA certificate.
 The TSF shall validate a certificate path by ensuring the presence of the basicConstraints
extension and that the CA flag is set to TRUE for all CA certificates.
 The TSF shall validate the revocation status of the certificate using [Online Certificate
Status Protocol (OCSP) as specified in RFC 2560].
 The TSF shall validate the extendedKeyUsage field according to the following rules:
o Certificates used for trusted updates and executable code integrity verification shall
have the Code Signing purpose (id-kp 3 with OID 1.3.6.1.5.5.7.3.3) in the
extendedKeyUsage field.
o Server certificates presented for TLS shall have the Server Authentication purpose
(id-kp 1 with OID 1.3.6.1.5.5.7.3.1) in the extendedKeyUsage field.
o Client certificates presented for TLS shall have the Client Authentication purpose (id-
kp 2 with OID 1.3.6.1.5.5.7.3.2) in the extendedKeyUsage field.
o OCSP certificates presented for OCSP responses shall have the OCSP Signing
purpose (id-kp 9 with OID 1.3.6.1.5.5.7.3.9) in the extendedKeyUsage field.
FIA_X509_EXT.1.2 The TSF shall only treat a certificate as a CA certificate if the
basicConstraints extension is present and the CA flag is set to TRUE.
34
5.3.3.6 FIA_X509_EXT.2 X.509 Certificate Authentication
FIA_X509_EXT.2.1 The TSF shall use X.509v3 certificates as defined by RFC 5280 to support
authentication for [TLS, HTTPS], and [code signing for integrity verification, no additional
uses].
FIA_X509_EXT.2.2 When the TSF cannot establish a connection to determine the validity of a
certificate, the TSF shall [not accept the certificate].
5.3.3.7 FIA_X509_EXT.3 X.509 Certificate Requests
FIA_X509_EXT.3.1 The TSF shall generate a Certificate Request Message as specified by
RFC 2986 and be able to provide the following information in the request: public key and
[Common Name, Organization, Organizational Unit, Country].
FIA_X509_EXT.3.2 The TSF shall validate the chain of certificates from the Root CA upon
receiving the CA Certificate Response.
5.3.4 Security management (FMT)
5.3.4.1 FMT_MOF.1(1)/TrustedUpdate Management of security functions behaviour
FMT_MOF.1.1(1)/TrustedUpdate The TSF shall restrict the ability to enable the functions to
perform manual update to Security Administrators.
5.3.4.2 FMT_MTD.1 Management of TSF Data (for general TSF data)
FMT_MTD.1.1 The TSF shall restrict the ability to manage the TSF data to the Security
Administrators.
5.3.4.3 FMT_SMF.1 Specification of Management Functions
FMT_SMF.1.1 The TSF shall be capable of performing the following management functions:
 Ability to administer the TOE locally and remotely;
 Ability to configure the access banner;
 Ability to configure the session inactivity time before session termination or locking;
 Ability to update the TOE, and to verify the updates using [hash comparison] capability
prior to installing those updates;
 [Ability to configure audit behavior;
 Ability to configure the cryptographic functionality.]
35
5.3.4.4 FMT_SMR.2 Restrictions on Security Roles
FMT_SMR.2.1 The TSF shall maintain the roles:
 Security Administrator.
FMT_SMR.2.2 The TSF shall be able to associate users with roles.
FMT_SMR.2.3 The TSF shall ensure that the conditions
 The Security Administrator role shall be able to administer the TOE locally;
 The Security Administrator role shall be able to administer the TOE remotely
are satisfied.
5.3.5 Protection of the TSF (FPT)
5.3.5.1 FPT_SKP_EXT.1 Extended: Protection of TSF Data (for reading of all symmetric
keys)
FPT_SKP_EXT.1.1 The TSF shall prevent reading of all pre-shared keys, symmetric keys, and
private keys.
5.3.5.2 FPT_APW_EXT.1 Extended: Protection of Administrator Passwords
FPT_APW_EXT.1.1 The TSF shall store passwords in non-plaintext form.
FPT_APW_EXT.1.2 The TSF shall prevent the reading of plaintext passwords.
5.3.5.3 FPT_STM.1 Reliable time stamps
FPT_STM.1.1 The TSF shall be able to provide reliable time stamps for its own use.
5.3.5.4 FPT_TST_EXT.1: TSF Testing
FPT_TST_EXT.1.1 The TSF shall run a suite of self tests during initial start-up (on power on)
to demonstrate the correct operation of the TSF: FIPS Self-Tests.
5.3.5.5 FPT_TUD_EXT.1 Extended: Trusted Update
FPT_TUD_EXT.1.1 The TSF shall provide Security Administrators the ability to query the
currently executing version of the TOE firmware/software as well as the most recently installed
version of the TOE firmware/software.
FPT_TUD_EXT.1.2 The TSF shall provide Security Administrators the ability to manually
initiate updates to TOE firmware/software and [no other update mechanism].
FPT_TUD_EXT.1.3 The TSF shall provide a means to verify firmware/software updates to the
TOE using a [published hash] prior to installing those updates.
36
5.3.6 TOE Access (FTA)
5.3.6.1 FTA_SSL_EXT.1 TSF-initiated Session Locking
FTA_SSL_EXT.1.1 The TSF shall, for local interactive sessions, [
 lock the session - disable any activity of the user’s data access/display devices other
than unlocking the session, and requiring that the administrator re-authenticate to the
TSF prior to unlocking the session]
after a Security Administrator-specified time period of inactivity.
5.3.6.2 FTA_SSL.3 TSF-initiated Termination
FTA_SSL.3.1 Refinement: The TSF shall terminate a remote interactive session after a
Security Administrator-configurable time interval of session inactivity.
5.3.6.3 FTA_SSL.4 User-initiated Termination
FTA_SSL.4.1 The TSF shall allow Administrator-initiated termination of the Administrator’s
own interactive session.
5.3.6.4 FTA_TAB.1 Default TOE Access Banners
FTA_TAB.1.1 Refinement: Before establishing an administrative user session the TSF shall
display a Security Administrator-specified advisory notice and consent warning message
regarding use of the TOE.
5.3.7 Trusted Path/Channels (FTP)
5.3.7.1 FTP_ITC.1 Inter-TSF trusted channel
FTP_ITC.1.1 Refinement: The TSF shall be capable of using [SSH] to provide a trusted
communication channel between itself and authorized IT entities supporting the following
capabilities: audit server, [no other capabilities] that is logically distinct from other
communication channels and provides assured identification of its end points and protection of
the channel data from disclosure and detection of modification of the channel data.
FTP_ITC.1.2 The TSF shall permit the TSF, or the authorized IT entities to initiate
communication via the trusted channel.
FTP_ ITC.1.3 The TSF shall initiate communication via the trusted channel for
[communications with the following:
 external audit servers using SSH].
37
5.3.7.2 FTP_TRP.1 Trusted Path
FTP_TRP.1.1 Refinement: The TSF shall be capable of using SSH and TLS/HTTPS to
provide a communication path between itself and authorized remote administrators that is
logically distinct from other communication paths and provides assured identification of its end
points and protection of the communicated data from disclosure and provides detection of
modification of the channel data.
FTP_TRP.1.2 Refinement: The TSF shall permit remote administrators to initiate
communication via the trusted path.
FTP_TRP.1.3 The TSF shall require the use of the trusted path for initial administrator
authentication and all remote administration actions.
5.4 TOE SFR Dependencies Rationale for SFRs Found in NDcPP
The NDcPPv1.0 contains all the requirements claimed in this Security Target. As such the
dependencies are not applicable since the PP itself has been approved.
5.5 Security Assurance Requirements
5.5.1 SAR Requirements
The TOE assurance requirements for this ST are taken directly from the NDcPP which are
derived from Common Criteria Version 3.1, Revision 4. The assurance requirements are
summarized in the table below.
Table 16: Assurance Measures
Assurance Class Components Components Description
Security Target (ASE) ASE_CCL.1 Conformance claims
ASE_ECD.1 Extended components definition
ASE_INT.1 ST introduction
ASE_OBJ.1 Security objectives for the operational
environment
ASE_REQ.1 Stated security requirements
ASE_SPD.1 Security Problem Definition
ASE_TSS.1 TOE summary specification
Development (ADV) ADV_FSP.1 Basic Functional Specification
Guidance documents (AGD) AGD_OPE.1 Operational user guidance
AGD_PRE.1 Preparative User guidance
Life cycle support (ALC) ALC_CMC.1 Labeling of the TOE
ALC_CMS.1 TOE CM coverage
Tests (ATE) ATE_IND.1 Independent testing - sample
Vulnerability assessment (AVA) AVA_VAN.1 Vulnerability survey
38
5.5.2 Security Assurance Requirements Rationale
The Security Assurance Requirements (SARs) in this Security Target represent the SARs
identified in the NDcPPv1.0. As such, the NDcPP SAR rationale is deemed acceptable since the
PP itself has been validated.
5.6 Assurance Measures
The TOE satisfies the identified assurance requirements. This section identifies the Assurance
Measures applied by Cisco to satisfy the assurance requirements. The table below lists the
details.
Table 17 Assurance Measures
Component How requirement will be met
ADV_FSP.1 There are no specific assurance activities associated with ADV_FSP.1. The requirements on
the content of the functional specification information is implicitly assessed by virtue of the
other assurance activities being performed. The functional specification is comprised of the
information contained in the AGD_OPE and AGD_PRE documentation, coupled with the
information provided in the TSS of the ST. The assurance activities in the functional
requirements point to evidence that should exist in the documentation and TSS section; since
these are directly associated with the SFRs, the tracing in element ADV_FSP.1.2D is
implicitly already done and no additional documentation is necessary.
AGD_OPE.1 The Administrative Guide provides the descriptions of the processes and procedures of how
the administrative users of the TOE can securely administer the TOE using the interfaces that
provide the features and functions detailed in the guidance.
AGD_PRE.1 The Installation Guide describes the installation, generation, and startup procedures so that the
users of the TOE can put the components of the TOE in the evaluated configuration.
ALC_CMC.1 The AGD and ST implicitly meet this assurance requirement. The evaluator shall check the
ST to ensure that it contains an identifier (such as a product name/version number) that
specifically identifies the version that meets the requirements of the ST. Further, the evaluator
shall check the AGD guidance and TOE samples received for testing to ensure that the version
number is consistent with that in the ST.
ALC_CMS.1
ATE_IND.1 Cisco will provide the TOE for testing.
AVA_VAN.1 Cisco will provide the TOE for testing.
39
6 TOE SUMMARY SPECIFICATION
6.1 TOE Security Functional Requirement Measures
This chapter identifies and describes how the Security Functional Requirements identified above
are met by the TOE.
Table 18 How TOE SFRs are Met
TOE SFRs How the SFR is Met
FAU_GEN.1 The TOE generates an audit record that is stored internally within the TOE
whenever an audited event occurs. Audit records are stored in files in the file
system provided by the TOE’s modified BSD operating system component.
The TOE stores auditable events in separate log files containing related types of
audited data. The following log files together comprise the TSF audit trail by
covering all events listed in Table 15:
 HTTPS Logs - Records Web Proxy messages specific to the HTTPS
Proxy (when the HTTPS Proxy is enabled).
 Audit Logs - Records AAA (Authentication, Authorization, and
Accounting) events. Records all user interaction with the application
and command-line interfaces, and captures committed changes.
 System Logs - Records DNS, error, and commit activity.
 CLI Audit Logs - Records a historical audit of command line interface
activity.
 GUI Logs - Records history of page refreshes in the web interface.
GUI logs also include information about SMTP transactions, for
example information about scheduled reports emailed from the
appliance.
 Authentication Logs - record all successful user logins and failed user
authentication attempts.
 NTP Logs – Records changes to the system time made by the
Network Time Protocol.
 Updater Logs – record events for TOE updates
Note that the TOE generates various other log files that record information
about the behavior of the TOE, but these do not contain logs that satisfy the
TOE’s auditing requirements.
The TOE shall ensure that each auditable event is associated with the user that
triggered the event and as a result they are traceable to a specific user. For
example a human user, user identity, or related session ID would be included in
the audit record. For an IT entity or device, the IP address, MAC address, host
name, or other configured identification is presented. Each audit record
includes date and time of the audited event, type of event, subject identity, and
the outcome (success or failure) of the event. The auditable events comprise:
 Start-up and shutdown of the audit function - recorded in System Logs.
 Access to the TOE and System data - recorded in: CLI Audit Logs (for
console interfaces) and GUI logs; and Updater logs (TOE updates).
 Reading of information from the audit records - recorded in CLI and
40
TOE SFRs How the SFR is Met
GUI Logs.
 Unsuccessful attempts to read information from the audit records -
recorded in CLI Audit Logs and GUI Logs.
 All modifications to the audit configuration that occur while the audit
collection functions are operating - recorded in CLI Audit Logs and
GUI Logs.
 All use of the user identification and authentication - Audit Logs.
 All modifications in the behavior of the functions of the TSF -
recorded in CLI Audit Logs and GUI Logs.
 All modifications to the values of TSF data - recorded in recorded in
CLI Audit Logs, GUI Logs, and NTP Logs.
 Modifications to the group of users that are part of a role - recorded in
CLI Audit Logs and GUI Logs.
Administrators and Operators can access all audit information. The
administrators can manually download the log files by clicking a link to the log
directory on the Log Subscriptions page, then clicking the log file to access.
Depending on the browser, an authorized administrator can view the file in a
browser window, or open or save it as a text file. This method uses the
HTTP(S) protocol and is the default retrieval method.
Example audit events are included below:
< Date and time of the event> < type of event> < source IP> <subject
identity> <outcome> <url accessed with return HTTP headers>
Thu Nov 1 19:03:00 2012 Info: login:10.65.79.90 user:admin
session:XtL50wP9GB92YfjVerYb
Thu Nov 1 19:03:00 2012 Info: req:10.65.79.90 user:- id:XtL50wP9GB92YfjVerYb
303 POST /login HTTP/1.1 Mozilla/5.0 (Macintosh; Intel Mac OS X 10_7_4)
AppleWebKit/537.4 (KHTML, like Gecko) Chrome/22.0.1229.94 Safari/537.4
Thu Nov 1 19:03:02 2012 Info: req:10.65.79.90 user:admin
id:XtL50wP9GB92YfjVerYb 200 GET /monitor/user_report HTTP/1.1 Mozilla/5.0
(Macintosh; Intel Mac OS X 10_7_4) AppleWebKit/537.4 (KHTML, like Gecko)
Chrome/22.0.1229.94 Safari/537.4
Thu Nov 1 19:03:03 2012 Info: req:10.65.79.90 user:admin
id:XtL50wP9GB92YfjVerYb 200 GET /scfw/1y-8.0.0-366/navigation.css HTTP/1.1
Mozilla/5.0 (Macintosh; Intel Mac OS X 10_7_4) AppleWebKit/537.4 (KHTML, like
Gecko) Chrome/22.0.1229.94 Safari/537.4
Thu Nov 1 19:03:03 2012 Info: req:10.65.79.90 user:admin
id:XtL50wP9GB92YfjVerYb 200 GET /scfw/1y-8.0.0-366/widget/tablecols/table-cols-
min.css HTTP/1.1 Mozilla/5.0(Macintosh; Intel Mac OS X 10_7_4) AppleWebKit/537.4
(KHTML, like Gecko) Chrome/22.0.1229.94 Safari/537.4
Thu Nov 1 19:03:03 2012 Info: req:10.65.79.90 user:admin
id:XtL50wP9GB92YfjVerYb 200 GET /yui_webui HTTP/1.1 Mozilla/5.0 (Macintosh;
Intel Mac OS X 10_7_4) AppleWebKit/537.4 (KHTML, like Gecko)
Chrome/22.0.1229.94 Safari/537.4
Thu Nov 1 19:03:04 2012 Info: req:10.65.79.90 user:admin
id:XtL50wP9GB92YfjVerYb 200 GET /javascript?CSRFKey=f0fadf9c-fce3-43b6-
84ae-3b42f559bcd5&language=en-usHTTP/1.1 Mozilla/5.0 (Macintosh; Intel Mac OS
X 10_7_4) AppleWebKit/537.4 (KHTML, like Gecko) Chrome/22.0.1229.94
Safari/537.4
FAU_GEN.2 The TOE shall ensure that each auditable event is associated with the user that
triggered the event and as a result they are traceable to a specific user. For
example a human user, user identity, or related session ID would be included in
41
TOE SFRs How the SFR is Met
the audit record. For an IT entity or device, the IP address, MAC address, host
name, or other configured identification is presented. A sample audit record is
below:
Thu Nov 1 19:03:00 2012 Info: login:10.65.79.90 user:admin
session:XtL50wP9GB92YfjVerYb
FAU_STG_EXT.1 The TOE is configured to export the audit log records within each of the log
files listed below to a specified, external syslog server. The TOE protects
communications with an external syslog server via SCP over SSH. This must
be configured by an authorized administrator. Once configured, the TOE can
automatically provide the audit backups. The log files that must be configured
for export are:
 HTTPS Logs
 Audit Logs
 System Logs
 CLI Audit Logs
 GUI Logs
 Authentication Logs
 NTP Logs
 Updater Logs
Note that the TOE can also export various other log file’s audit records to an
external syslog server, but these other log files do not contain logs that satisfy
the TOE’s auditing requirements.
The TOE provides the following mechanisms for retrieving log files:
 SCP - a CLI client that supports an scp command can copy log files
from the TOE to the client host. The user of the scp command on the
client must be the admin user on the TOE, as the TOE will prompt for
the admin user password before processing the SCP request
 SCP Push - additionally, the TOE can be configured to periodically
push log files to a SCP server on a remote computer
Both of the above SCP methods are secured by SSHv2. The SCP is the method
that periodically pushes log files to a SCP server on a remote syslog server.
This method requires an SSH SCP server on a remote computer using SSHv2
protocol. The subscription requires a username, SSH key, and destination
directory on the remote syslog server. Log files are transferred based on a
rollover schedule set by the authorized administrator. The TOE generates an
email alert to the authorized administrator or System administrator and begins
overwriting the oldest stored audit records when the audit trail becomes full.
(Note that the TOE does not stop collecting or producing System data). The
alert is generated to an authorized administrator or System administrator who
has been configured via the command line interface (alertconfig command)
to receive email alerts for this event. The TOE does not provide interfaces to
modify individual records. When the audit trail becomes full, the TOE ensures
that the most recent audit records will be maintained, limited only by the
available storage space.
This method periodically pushes log files to an SCP server on a remote syslog
server. This method requires an SSH SCP server on a remote computer using
SSHv2 protocol. The subscription requires a username, SSH key, and
42
TOE SFRs How the SFR is Met
destination directory on the remote syslog server. Log files are transferred
based on a rollover schedule set by the authorized administrator.
The TOE is capable of detecting when the SSH connection fails. The TOE also
stores a local set of audit records on the TOE, and continues to do so if the
communication with the syslog server goes down. The TOE stores the audit
logs locally as configured with the logconfig command in the CLI and the Log
Subscriptions page in the GUI. The size of the local log files are set by an
authorized administrator using the 'Rollover by File Size' configuration setting.
Once the file reaches the specified size it is sent to the syslog server using SCP.
These transfers can also be configured based on configured time intervals.
If the SSH connection fails, the log files will remain on the TOE. On the next
SCP push based on either the maximum log file size being exceeded or on the
time interval, the current log file and the log files previously unsuccessfully
transferred will be transferred.
Only Authorized Administrators are able to clear the local logs, and there is no
TOE interface that allows for administrators to modify the contents of the local
audit records.
The TOE’s default installation configures the audit log files to maintain 10 files
of no more than 10MB for each log subscription. The administrative user does
not need to configure this. However, this value is customizable. The
administrative user can configure each log subscription to allow 1-1000
maximum log files, and each log file can be configurable to a maximum of
between 100KB and 100MB. There is no limit to the number of log
subscriptions that the administrative user can create.
With a typical configuration, the log space should not grow beyond a
reasonable limit. If through customization of the log limits, the log files grow
too much, alerts will be sent to the administrator when the log partition grows
beyond 90% usage. If the space available for storing audit records is exhausted,
the TOE will start to overwrite the oldest records in the audit trail, and generate
an email alert to this effect and send it to an Administrator.
FCS_CKM.1
FCS_CKM.2
The TOE generates asymmetric keys in accordance with the RSA schemes
using key sizes of 2048-bit or greater that are conformant to the NIST SP 800-
56B. In addition, ECC schemes are used with P-256, P-384, and P-521. The
TOE can create a RSA public-private key pair that can be used to generate a
Certificate Signing Request (CSR). Via offline CSR the TOE can send the CSR
to a Certificate Authority (CA) for the CA to generate a certificate; and receive
its certificate (including X.509v3) from the CA. Integrity of the CSR and
certificate during transit are assured through use of digital signatures
(encrypting the hash of the TOE’s public key contained in the CSR and
certificate). The TOE can store and distribute the certificate to external entities
including Registration Authorities (RA). The TOE can also use X.509v3
certificates for authentication of TLS sessions. The TOE acts as both a sender
and receiver for RSA-based key establishment schemes 800-56A and 800-56B.
The key pair generation portions of "The RSA Validation System" for FIPS
186-4 were used as a guide in testing the FCS_CKM.1.
ECDH is used for key exchange for the SSHv2 sessions. For details on each
protocol see the related SFR.
FCS_CKM.4 The TOE meets all requirements for destruction of keys and Critical Security
Parameters (CSPs) in that none of the symmetric keys, pre-shared keys, or
43
TOE SFRs How the SFR is Met
private keys are stored in plaintext form as described in Table 19.
The TOE zeroizes all of the cryptographic keys used within the TOE after the
key is no longer of use to the TOE. The cryptographic module performs the
overwrite of the cryptographic keys and other critical security parameters that
are handled by the CiscoSSL library are zeroized using a function that will
overwrite the memory with random data once they are no longer in use. Swap
space is encrypted using AES to avoid accidental leakage of CSPs. As part of
the reload command, an option to wipe the data is provided. The wipe option
along with the 'wipedata' command will overwrite the hard drive with zeros so
that the keys are zeroized within the old core dump files. See Table 19 in
Section 7.1, below for more information.
FCS_COP.1(1) The TOE provides symmetric encryption and decryption capabilities using AES
in CBC mode (128 and 256 bits) as described in ISO 18033-3 and ISO 10116.
AES is implemented in the following protocols: TLSv1.1, TLSv1.2 and SSHv2.
The TOE provides AES encryption and decryption in support of SSHv2 and
TLSv1.2 for secure communications. Management of the cryptographic
algorithms is provided through the CLI with auditing of those commands.
FCS_COP.1(2) The TOE provides cryptographic signature services using the following:
 RSA Digital Signature Algorithm with key size of 2048 and
greater as specified in FIPS PUB 186-4, “Digital Signature
Standard”.
The TOE provides cryptographic signatures in support of SSHv2, and TLS for
secure communications. Management of the cryptographic algorithms is
provided through the CLI with auditing of those commands. The TOE
provides the RSA option in support of SSHv2 and TLS key establishment.
RSA (3072-bit and 4096-bit) is used in the establishment of SSHv2 key
establishment. For SSHv2, RSA host keys are supported
FCS_COP.1(3) The TOE provides cryptographic hashing services using SHA-1, SHA-256,
SHA-384, and SHA-512 as specified in ISO/IEC 10118-3:2004. The TOE
provides hashing as part of the TLS session integrity. WSA uses server side
X.509v3 certificates for authentication. Digital signature is comprised of
implementing an encrypted hash function. Verification of the digital signature
includes the process of decrypting the encrypted hash and verifying the hash is
valid. SHA1 is also used in the keyed hash function of HMAC.
The TOE provides Secure Hash Standard (SHS) hashing in support of TLS, for
secure communications. Management of the cryptographic algorithms is
provided through the CLI with auditing of those commands.
FCS_COP.1(4) The TOE provides keyed-hashing message authentication services using
HMAC-SHA1, key size 160 bits, and message digest sizes 160 bits as specified
in ISO/IEC 9797-2:2011, Section 7 “MAC Algorithm 2”. The block size for
HMAC-SHA1 is 512 bits.
The TOE provides SHS hashing and HMAC message authentication in support
of SSHv2, and TLSv1.2 for secure communications. Management of the
cryptographic algorithms is provided through the CLI with auditing of those
commands.
SHS hashing and HMAC message authentication (SHA-1) is used in the
establishment of TLS/HTTPS, and SSHv2 sessions.
FCS_HTTPS_EXT.1 The TOE implements HTTPS over TLS as specified in RFC 2818 and
44
TOE SFRs How the SFR is Met
FCS_TLSS_EXT.1. The TSF HTTPS implementation authenticates the TOE to
the remote client with an X.509 certificate. System Administrators manage the
TOE identity certificates using the Destination Controls page in the GUI or
destconfig command in the TOE CLI. HTTPS uses the Security Administrator
- selected identity certificate.
The TSF HTTPS implementation performs server based authentication using a
server X.509v3 certificate to establish the TLS session. The TSF HTTPS
implementation does not require client authentication at the TLS level but
presents the Web interface logon page for administrative users to authenticate
using their name and password.
FCS_RBG_EXT.1 The TOE implements a NIST-approved Deterministic Random Bit Generator
(DRBG), as specified in ISO/IEC 18031:2011 per NIST SP800-90A using
Hash_DRBG (any), HMAC_DRBG (any), and CTR_DRBG (AES). The TOE
models provide a software based entropy source as described in
FCS_RBG_EXT.1. This output is used directly to seed the DRBG.
The TOE implements a random number generator for Elliptic Curve Diffie-
Hellman based key establishment (conformant to NIST SP 800-56A) and for
RSA key establishment (conformant to NIST SP 800-56B. The TOE complies
with section 5.6 and all subsections regarding asymmetric key pair generation
and key establishment in the NIST SP 800-56A. The TOE complies with
section 6 and all subsections regarding RSA key pair generation and key
establishment in the NIST SP 800-56B.
The TOE is able to generate asymmetric key pairs with modulus 2048 bits
which is equivalent to a symmetric key strength of 112 bits.
FCS_SSHC_EXT.1 The TOE implements SSHv2 to secure the remote session between the TOE
and syslog server. SSHv2 is implemented according to the following RFCs:
4251, 4252, 4253, and 4254. The TOE supports public key-based
authentication. The TOE uses a SCP push to securely send the audit logs to a
remote syslog server over a secured SSHv2 session. The SSH client
authenticates the identity of the SSH server using a local database associating
each host name with its corresponding public key RFC 4251 section 4.1.
SSH connections will be dropped if the TOE receives a packet larger than
35,000 bytes. Large packets are detected by the SSH implementation, and
dropped internal to the SSH process. A rekey occurs after a threshold of no
longer than one hour, and no more than one gigabyte of transmitted data. The
key exchange methods used by the TOE is a configurable option but diffie-
hellman-group14-sha1 is the only allowed method within the evaluated
configuration. Any session where the SSH server offers only non compliant
algorithms or key sizes per the NDcPP will be rejected by the SSH client. SSH
sessions can only be established when compliant algorithms and key sizes can
be negotiated.
The TOE implementation of SSHv2 supports the following:
 public key algorithms for authentication: ssh-rsa.
 encryption algorithms, aes128-cbc, aes256-cbc to ensure
confidentiality of the session.
 hashing algorithms HMAC-SHA1 to ensure the integrity of the
session.
FCS_SSHS_EXT.1 The TOE implements SSHv2 for remote CLI sessions (telnet is disabled in the
45
TOE SFRs How the SFR is Met
evaluated configuration). SSHv2 is implemented according to the following
RFCs: 4251, 4252, 4253, and 4254. The TOE supports both public key-based
and password-based authentication. Remote CLI SSHv2 sessions are limited to
an administrator configurable session timeout period, and will be rekeyed after
a threshold of no longer than one hour, and no more than one gigabyte of
transmitted data.
SSH connections will be dropped if the TOE receives a packet larger than
35,000 bytes. Large packets are detected by the SSH implementation, and
dropped internal to the SSH process. The key exchange methods used by the
TOE is a configurable option but diffie-hellman-group14-sha1 is the only
allowed method within the evaluated configuration. Any session where the
SSH client offers only non compliant algorithms or key sizes per the NDcPP
will be rejected by the SSH server. SSH sessions can only be established when
compliant algorithms and key sizes can be negotiated.
The TOE implementation of SSHv2 supports the following:
 public key algorithms for authentication: ssh-rsa.
 password-based authentication for administrative users accessing the
TOE's CLI through SSHv2.
 encryption algorithms, AES-CBC-128, AES-CBC-256 to ensure
confidentiality of the session.
 hashing algorithms HMAC-SHA1 to ensure the integrity of the
session.
FCS_TLSS_EXT.1 An authorized administrator can initiate inbound TLSv1.1 and TLSv1.2
connections using the web based GUI for remote administration of the TOE.
The TOE uses TLS for inbound/outbound Web traffic handling. Any session
where the client offers the following in the client hello: SSL 2.0, SSL 3.0 and
TLS 1.0 will be rejected by the TLS server. Since RSA is being used for key
exchange and authentication there are no specific parameters associated with
the server key exchange. Using the below TLS_RSA ciphers the RSA public
key is used for authentication and key exchange. Using the below TLS_DHE
ciphers the standard diffie hellman parameters P, Q, and G are used for key
exchange.
TLS is also used to protect the TLS sessions with the TOE, which supports the
mandatory ciphersuite as well as the following optional ciphersuite:
 TLS_RSA_WITH_AES_128_CBC_SHA
 TLS_RSA_WITH_AES_256_CBC_SHA
 TLS_RSA_WITH_AES_128_CBC_SHA256
 TLS_RSA_WITH_AES_256_CBC_ SHA256
 TLS_ECDHE_RSA_WITH_AES_128_CBC_SHA
 TLS_ECDHE_RSA_WITH_AES_256_CBC_SHA
 TLS_ECDHE_RSA_WITH_AES_256_GCM_SHA384
 TLS_ECDHE_RSA_WITH_AES_128_GCM_SHA256
FIA_PMG_EXT.1 The TOE supports the local definition of users with corresponding passwords.
The passwords can be composed of any combination of upper and lower case
letters, numbers, and special characters (that include: “!”, “@”, “#”, “$”, “%”,
“^”, “&”, “*”, “(”, and “)”. Minimum password length is settable by the
Authorized Administrator, and can be configured for minimum password
lengths of 15 characters.
FIA_UIA_EXT.1
FIA_UAU_EXT.2
The TOE requires all users to be successfully identified and authenticated
before allowing any TSF mediated actions to be performed, except for the login
46
TOE SFRs How the SFR is Met
banner that is displayed prior to user authentication. Administrative access to
the TOE is facilitated through the TOE’s CLI and web based GUI. The TOE
mediates all administrative actions through the CLI and web based GUI. Once
a potential administrative user attempts to access the CLI via either a directly
connected console or remotely through SSHv2, the TOE prompts the user for a
user name and password. Likewise, when a potential administrative user
attempts to access the web based GUI of the TOE through a TLSv1.1 or
1.2/HTTPS, the TOE prompts the user for a user name and password. Only
after the administrative user presents the correct authentication credentials will
access to the TOE administrative functionality be granted. No access is allowed
to the administrative functionality of the TOE until an administrator is
successfully identified and authenticated.
The TOE provides a local password based authentication mechanism for the
CLI when accessed both locally and remotely as well as the GUI. The
password mechanism can be configured to require passwords to be a minimum
of 15 characters from the printable character set. The TOE prevents
administrative user actions from being performed prior to identification and
authentication of the user (all filtering of web traffic occurs without
identification or authentication of users).
The TOE defines a default user account, called admin. This account has all
administrative privileges. The TOE allows additional administrative accounts
to be created. Each account comprises a user name (which identifies the user),
authentication data, in the form of a password, and authorizations, in the form
of a group assignment that grants certain administrative privileges. Assigning a
group to a user account essentially confers a security management role on that
user.
Note, however, that users accessing the CLI via SSHv2 can be authenticated
using public key cryptography. This requires the user’s public key to be
entered into the TOE (using the sshconfig command) and associated with the
user’s account. If there is no public key configured for the user, the user will
instead be prompted to enter a password to authenticate.
FIA_UAU.7 When a user enters their password at the local console, the TOE does not echo
any characters as they are entered as such the user password is obscured.
Likewise, for remote CLI session authentication, the TOE does not echo any
characters as they are entered.
FIA_X509_EXT.1
FIA_X509_EXT.2
FIA_X509_EXT.3
The TOE uses X.509v3 certificates as defined by RFC 5280 to support
authentication for TLS connections. The certificate validation checking takes
place during the TLS session setup.
The TOE supports the following methods to obtain a certificate from a CA:
 Manual cut-and-paste - WSA generates the Certificate Request
Message as described in RFC 2986 which contains the public key and
is displayed via the GUI or CLI interface. This allows the
administrator to copy the certificate request and in an secure offline
manner send the request to a Certification Authority to be transformed
into an X.509v3 public-key certificate.
 Both the certificate request message and the certificates themselves
provide protection in that they are digitally signed. If a certificate is
modified in any way, it would be invalidated. The digital signature
verifications process would show that the certificate had been
47
TOE SFRs How the SFR is Met
tampered with when the hash value would be invalid.
 The certificate chain establishes a sequence of trusted certificates,
from a peer certificate to the root CA certificate. Within the PKI
hierarchy, all enrolled peers can validate the certificate of one another
if the peers share a trusted root CA certificate or a common
subordinate CA. When a certificate chain is received from a peer, the
default processing of a certificate chain path continues until the first
trusted certificate is reached.
 The authorized administrator can also configure one or more
certificate fields as listed below that will be used to compare the
imported certificate to specific criteria such as:
• alt-subject-name (If subject name doesn’t match request,
then the alternative subject name filed is used)
• expires-on (If certificate is expired, rejects certificate)
• issuer-name (Is there a trusted root certificate installed for
the CA that signed the certificate).
• name (Does the name in the request match the name in the
certificate)
• serial-number (Has the certificate been revoked. Serial
number will be in the CRL/OCSP)
• subject-name (Does the name in the request match the name
in the certificate)
More than one certificate from one or more CAs on the TOE can be stored and
used by WSA. For example, one certificate from one CA could be used for
SSH connections, while another certificate from another CA could be used for
TLS connections.
The administrative user manually installs and selects the certificate used by the
TOE for each purpose.
The physical security of the TOE (A.PHYSICAL_PROTECTION) protects the
switch and the certificates from being tampered with or deleted. In addition,
the TOE identification and authentication security functions protect an
unauthorized user from gaining access to the TOE.
The use of Online Certificate Status Protocol (OCSP) is configurable and may
be used for certificate revocation.
• OCSP --Certificate checking is performed by a OCSP server. This is the
default option.
Checking is also done for the basicConstraints extension and the CA flag to
determine whether they are present and set to TRUE. The local certificate that
was imported must contain the basic constraints extension with the CA flag set
to true, the check also ensure that the key usage extension is present, and the
keyEncipherment bit or the keyAgreement bit or both are set. If they are not,
the certificate is not accepted.
If the connection to determine the certificate validity cannot be established,
WSA does not accept the certificate.
FMT_MOF.1.1(1)/TrustedUpdate Manual software updates can only be done by the authorized administrator
through either the CLI or GUI. These updates include software upgrades.
FMT_MTD.1 The TOE provides administrative users with a CLI and web based GUI to
interact with and manage the security functions of the TOE. The CLI is the
48
TOE SFRs How the SFR is Met
main interface used to administer the TOE since all functionality to configure
and monitor the system is here. The GUI contains most of the functionality an
authorized administrator needs to configure and monitor the system. However,
not all CLI commands are available in the GUI; some features are only
available through the CLI. The CLI is used to perform all security functions,
including configuring the WSA appliance and managing users and email
security policies.
No administrative functionality is available prior to administrative login.
Through the CLI, the TOE provides the ability for Authorized Administrators to
manage TOE data, such as audit data, configuration data, security attributes,
message filters, login banners, and mail policies via the CLI and GUI. A subset
of functionality is available in the GUI. Each of the predefined and
administratively configured privilege levels has a set of permissions that will
grant them access to the TOE data, though with some privilege levels, the
access is limited. The TOE performs role-based authorization, using TOE
platform authorization mechanisms, to grant access to the semi-privileged and
privileged levels. The term “Authorized Administrator” is used in this ST to
refer to any user which has been assigned to a privilege level that is permitted
to perform the relevant action; therefore has the appropriate privileges to
perform the requested functions. Therefore, semi-privileged administrators
with only a subset of privileges can also modify TOE data based on if granted
the privilege. See FMT_SMR.2 for more details on the TOE roles and related
privileges.
FMT_SMF.1 The TOE provides all the capabilities necessary to securely manage the TOE.
The administrative user can connect to the TOE using the CLI to perform these
functions via SSHv2, the local console, or via the GUI over TLS/HTTPS.
The specific management capabilities available from the TOE include:
 Local and remote administration of the TOE and the services provided
by the TOE via the TOE CLI, as described above;
 The ability to update the AsyncOS software (image integrity
verification is provided using SHA-384)
 Ability to configure the cryptographic functionality;
 Ability to enable, disable, determine and modify the behavior of all the
security functions of the TOE via the CLI and GUI.
 Configure access banner
 Configure session inactivity time before session termination or
locking,
 Ability to configure the audit behavior.
FMT_SMR.2 The TOE platform maintains privileged and semi-privileged administrator
roles. The TOE performs role-based authorization, using TOE platform
authorization mechanisms, to grant access to the semi-privileged and privileged
roles. The default user account for the system, admin, has all administrative
privileges. The admin user account cannot be deleted, but an authorized
administrator can change the password and lock the account. When an
authorized administrator creates a new user account, they can assign the user to
a predefined or a custom user role. Each role contains differing levels of
permissions within the system. Although there is no limit to the number of user
accounts that an authorized administrator can create on the appliance,
authorized administrator cannot create user accounts with names that are
49
TOE SFRs How the SFR is Met
reserved by the system such as “operator” or “root.” The following roles are
predefined by the system and can be assigned to user accounts:
 Administrator - Allows full access to all system configuration settings.
However, the upgradecheck and upgradeinstall CLI commands can
be issued only from the system defined “admin” account.
 Operator - Restricts users from creating, editing, or removing user
accounts. The operators group also restricts the use of the following
CLI commands:
 resetconfig
 upgradecheck
 upgradeinstall
 systemsetup
 Read-Only Operator - User accounts with this role:
 Can view configuration information.
 Can make and submit changes to see how to
configure a feature, but they cannot commit them.
 Cannot make any other changes to the appliance,
such as clearing the cache or saving files.
 Cannot access the file system, FTP, or SCP.
 Guest - The guests group users can only view system status
information, including reporting and tracking.
The term “authorized administrator” is used in this ST to refer to any user
which has been assigned to a privilege level that is permitted to perform the
relevant action; therefore has the appropriate privileges to perform the
requested functions. The assigned role determines the functions the user can
perform; hence the authorized administrator with the appropriate privileges.
The TOE can and shall be configured to authenticate all access to the CLI and
GUI using a username and password.
The TOE supports both local administration via a directly connected console
cable and remote authentication via SSHv2 and TLS/HTTPS.
FPT_SKP_EXT.1
FPT_APW_EXT.1
The TOE stores all private keys encrypted using AES-128. All pre-shared and
symmetric keys are stored in encrypted form using AES-128 using the intel
Xeon AES-NI encryption. The TOE is configured to be in FIPS mode by
entering the 'fipsconfig' command at the CLI. During the FIPS mode setup, an
authorized administrator is able to select the option to have all passwords and
keys encrypted. In addition, there is a sub-option using the 'saveconfig'
command and the save config dialog in the GUI to encrypt the passwords and
keys.
There are no administrative interfaces available that allow passwords to be
viewed.
FPT_STM.1 The TOE provides a source of date and time information used in audit event
timestamps. The clock function is reliant on the system clock provided by the
underlying hardware. The TOE can optionally be set to receive clock updates
from an NTP server using the ‘ntpconfig’ command or via the GUI in the Time
Zone or Time Settings page from the System Administration menu. This date
and time is used as the time stamp that is applied to TOE generated audit
records and used to track inactivity of administrative sessions. The time
information is also used in setting the system time and administrative session
timeout. The time can be configured using the CLI commands: settime and
settz. In the GUI, the time can be configured under the Time Zone or Time
Settings page from the System Administration menu.
50
TOE SFRs How the SFR is Met
FPT_TST_EXT.1 The TOE runs a suite of self-tests during initial start-up to verify its correct
operation also referred to as Power on Self-Tests (POST). The POST verifies
the integrity of the software and ensures all cryptographic software. If any of
the tests fail, the Authorized Administrator will have to log into the CLI to
determine which test failed and why.
During the system bootup process (power on or reboot), all the Power on
Startup Test (POST) components for all the cryptographic modules perform the
POST for the corresponding component (hardware or software). These tests
include:
 Data integrity of the message queue store journal
 checks a known virus (spam) stamp against anti-virus (-spam) engines
 AES Known Answer Test
 AES-CCM Known Answer Test
 AES-GCM Known Answer Test
 AES-CMAC Known Answer Test
 Triple-DES Known Answer Test
 DSA Sign/Verify Test
 RSA Signature Known Answer Test
 ECDSA Sign/Verify Test
 RNG Known Answer Test
 HMAC Known Answer Test (performed for each supported SHA)
 SHA-1 Known Answer Test
 SHA-2 Known Answer Test (includes SHA-224, SHA-256, SHA-384
and SHA-
 512)
 Software Integrity Test
If any component reports failure for the POST, the system crashes and
appropriate information is displayed on the screen, and an alert is sent to an
administrative email each time a self test fails for any reason and a failed part of
the functionality is disabled until a problem resolution has been accomplished.
All ports are blocked from moving to forwarding state during the POST. If all
components of all modules pass the POST, the system is placed in FIPS PASS
state and ports are allowed to forward data traffic.
These tests are sufficient to verify that the correct version of the TOE software
is running as well as that the cryptographic operations are all performing as
expected. Both of these functions are required to ensure that the TOE is
operating as expected and data that the user expects to be encrypted in not
transferred in plaintext.
FPT_TUD_EXT.1 An Authorized Administrator can query the currently executing software
version as well as the last installed version via the CLI and GUI. An authorized
administrator can either manually download the updates or WSA can
automatically download the updates when "automated updates" has been
configured. Updates can be downloaded directly from the Cisco Update
Servers as well as from an offline update server. Both an administrator and the
TOE can check to see if an update is available from Cisco. If automated
updates have been configured by an Authorized Administrator, then the TOE
downloads the update which is an encrypted file and a config file with a hash of
the update. The TOE decrypts the update. Verification of the authenticity of
the image and software updates is done in an automated manner. WSA
automatically compares the hash received via the configuration file to the hash
51
TOE SFRs How the SFR is Met
computed for the product update using SHA-384. If there is a checksum
mismatch, the update will not be installed. Attempts to perform an illegitimate
update onto the system will be logged into updater logs at INFO level. The
sample log line will look as follows:
Wed Dec 11 05:50:07 2013 Info: repeng SHA384
Mismatch
FTA_SSL_EXT.1
FTA_SSL.3
An administrator can configure maximum inactivity times individually for both
the CLI and GUI. An authorized administrator can specify how long a user can
be logged into the Web Security appliance’s Web UI before AsyncOS logs the
user out due to inactivity by default it is set to 30 minutes. This Web UI session
timeout applies to all users, including administrators, and it is used for both
HTTP and HTTPS sessions. For this purposes of the evaluated configuration
only HTTPS is permitted. Once AsyncOS logs a user out, the appliance
redirects the user’s web browser to the login page.
Likewise an authorized administrator can specify how long a user can be logged
into the Web Security appliance’s CLI before AsyncOS logs the user out due to
inactivity.
If a local user session is inactive for a configured period of time, the session
will be locked and will require re-authentication to unlock the session. If a
remote user session is inactive for a configured period of time, the session will
be terminated and will require authentication to establish a new session.
FTA_SSL.4 An administrator is able to exit out of both the CLI and GUI administrative
sessions. An authorized administrator can log out of the CLI with the 'exit'
command. The Web UI also has a logout option via the drop-down menu.
FTA_TAB.1 The TOE displays an authorized administrator specified banner on the CLI and
GUI management interfaces prior to allowing any administrative access to the
TOE. This is applicable for both the CLI and GUI being accessed locally and
remotely
FTP_ITC.1 The TOE protects communications with the syslog server using SSHv2. SSHv2
uses a keyed hash as defined in FCS_SSHC_EXT.1.6. This protects the data
from modification by hashing the data and verifying the hash on receipt of the
data. This ensures that the data has not been modified in transit. In addition,
encryption of the data as defined in FCS_SSHC_EXT.1.4 is provided to ensure
the data is not disclosed in transit.
SCP Push is used for sending audit logs securely over SSHv2 to a syslog server.
This method periodically pushes log files to a remote Syslog server. It requires
an SSH server on the Syslog Server using the SSHv2 protocol. The
subscription requires a username, SSH key, and destination directory on the
remote computer. Log files are transferred based on a rollover schedule set by
an Authorized Administrator.
FTP_TRP.1 All remote administrative communications take place over a secure encrypted
SSHv2 for the CLI or TLS/HTTPS for the GUI sessions. The SSHv2 session is
encrypted using AES encryption. The remote users are able to initiate SSHv2
communications with the TOE for secure CLI access. TLS/HTTPS is used to
secure the communications with the TOE and remote web browser for secure
GUI access.
52
7 ANNEX A: KEY ZEROIZATION
7.1 Key Zeroization
The following table describes the key zeroization referenced by FCS_CKM.4 provided by the
TOE.
Table 19: TOE Key Zeroization
Name Description Zeroization
Diffie-Hellman
Shared Secret
The value is zeroized after it has been given back to the
consuming operation. The value is overwritten by 0’s.
Automatically after
completion of DH
exchange.
Overwritten with: 0x00
Diffie Hellman
private exponent
The function returns the value to the RP and then calls the
function to perform the zeroization of the generated key pair
(p_dh_kepair) and then calls the standard Linux free (without the
poisoning). These values are automatically zeroized after
generation and once the value has been provided back to the
actual consumer.
Zeroized upon completion
of DH exchange.
Overwritten with: 0x00
SSH Private Key Once the function has completed the operations requiring the
RSA key object, the module over writes the entire object (no
matter its contents) using memset. This overwrites the key with
all 0’s.
Zeroized upon deletion of
the SSH public/private key
pair when no longer needed.
Overwritten with: 0x00
AES Key The results zeroized using the poisoning in free to overwrite the
values with 0x00. This is called by the ssh_close function when a
session is ended.
Automatically when the
SSH/TLS session is
terminated.
Overwritten with: 0x00
53
ANNEX B: REFERENCES
The following documentation was used to prepare this ST:
Table 20: References
Identifier Description
[CC_PART1] Common Criteria for Information Technology Security Evaluation – Part 1: Introduction
and general model, dated September 2012, version 3.1, Revision 4, CCMB-2012-009-001
[CC_PART2] Common Criteria for Information Technology Security Evaluation – Part 2: Security
functional components, dated September 2012, version 3.1, Revision 4, CCMB-2012-009-
002
[CC_PART3] Common Criteria for Information Technology Security Evaluation – Part 3: Security
assurance components, dated September 2012, version 3.1, Revision 4, CCMB-2012-009-
003
[CEM] Common Methodology for Information Technology Security Evaluation – Evaluation
Methodology, dated September 2012, version 3.1, Revision 4, CCMB-2012-009-004
[NDcPP] collaborative Protection Profile for Network Devices, version 1.0, 27-Feb-2015
[800-38A] NIST Special Publication 800-38A Recommendation for Block 2001 Edition
Recommendation for Block Cipher Modes of Operation Methods and Techniques December
2001
[800-56A] NIST Special Publication 800-56A Rev 2, May 2013
Recommendation for Pair-Wise Key Establishment Schemes Using Discrete Logarithm
Cryptography
[800-56B] NIST Special Publication 800-56B Recommendation for Pair-Wise, August 2009
Key Establishment Schemes Using Integer Factorization Cryptography
[FIPS 140-2] FIPS PUB 140-2 Federal Information Processing Standards Publication
Security Requirements for Cryptographic Modules May 25, 2001
[FIPS PUB 186-2] FIPS PUB 186-2 Federal Information Processing Standards Publication 2000 January 27
[FIPS PUB 186-3] FIPS PUB 186-3 Federal Information Processing Standards Publication Digital Signature
Standard (DSS) June, 2009
[FIPS PUB 186-4] FIPS PUB 186-4 Federal Information Processing Standards Publication Digital Signature
Standard (DSS) July 2013
[FIPS PUB 198-1] Federal Information Processing Standards Publication The Keyed-Hash Message
Authentication Code (HMAC) July 2008
[NIST SP 800-
90A Rev 1]
NIST Special Publication 800-90A Recommendation for Random Number Generation
Using Deterministic Random Bit Generators January 2015
[FIPS PUB 180-3] FIPS PUB 180-3 Federal Information Processing Standards Publication Secure Hash
Standard (SHS) October 2008
54
ANNEX C: TECHNICAL DECISIONS
The following Technical Decisions apply to the NDcPPv1.0:
Table 21 NDcPP Technical Decisions
ID Description PP Relates to Date
TD0201
NIT Technical Decision for Use of
intermediate CA certificates and certificate
hierarchy depth
CPP_ND_V1.0, CPP_FW_V1.0, ND SD
v1.0, FIA_X509_EXT.1.1,
FIA_X509_EXT.1.2
2017.05.03
TD0200
NIT Technical Decision for Password
authentication for SSH clients
CPP_ND_V1.0, CPP_FW_V1.0, ND SD
v1.0, FCS_SSHC_EXT.1.2
2017.05.01
TD0199
NIT Technical Decision for Elliptic
Curves for Signatures
CPP_ND_V1.0, CPP_FW_V1.0,
FCS_COP.1
2017.05.01
TD0195
NIT Technical Decision Making DH
Group 14 optional in
FCS_IPSEC_EXT.1.11
CPP_ND_V1.0, CPP_FW_V1.0,
FCS_IPSEC_EXT.1.11
2017.04.21
TD0191
NIT Technical Decision for Using
secp521r1 for TLS communication
CPP_ND_V1.0, CPP_FW_V1.0,
FCS_TLSS_EXT.1.3. FCS_TLSS_EXT.2.3
2017.04.10
TD0189
NIT Technical Decision for SSH Server
Encryption Algorithms
NDcPP V1.0, FWcPP V1.0,
FCS_SSHC_EXT.1.4,
FCS_SSHS_EXT.1.4
2017.04.10
TD0188
NIT Technical Decision for Optional use
of X.509 certificates for digital signatures
NDcPP V1.0, FWcPP V1.0,
FPT_TUD_EXT.1, FPT_TUD_EXT.2
2017.04.10
TD0187
NIT Technical Decision for Clarifying
FIA_X509_EXT.1 test 1
NDcPP V1.0, FWcPP V1.0, ND SD v1.0,
FIA_X509_EXT.1.1
2017.04.10
TD0186
NIT Technical Decision for Applicability
of X.509 certificate testing to IPsec
NDcPP V1.0, FWcPP V1.0,
FIA_X509_EXT.1.1
2017.04.10
TD0185
NIT Technical Decision for Channel for
Secure Update.
NDcPP V1.0, FWcPP V1.0,
FPT_TUD_EXT.1, FTP_ITC.1
2017.04.10
TD0184
NIT Technical Decision for Mandatory
use of X.509 certificates
NDcPP V1.0, FWcPP V1.0,
FIA_X509_EXT.1, FIA_X509_EXT.2,
FIA_X509_EXT.3
2017.04.10
TD0182
NIT Technical Decision for Handling of
X.509 certificates related to ssh-rsa and
remote comms.
NDcPP V1.0, FWcPP V1.0,
FIA_X509_EXT.1, FIA_X509_EXT.2,
FIA_X509_EXT.3
2017.04.10
TD0181
NIT Technical Decision for Self-testing of
integrity of firmware and software.
NDcPP V1.0, FWcPP V1.0, ND SD V1.0,
FPT_TST_EXT.1
2017.04.10
TD0170
NIT Technical Decision for SNMPv3
Support
CPP_ND_V1.0, CPP_FW_V1.0,
FTP_TRP.1
2017.04.04
TD0169
NIT Technical Decision for Compliance to
RFC5759 and RFC5280 for using CRLs
CPP_ND_V1.0, CPP_FW_V1.0,
FIA_X509_EXT.1.1
2017.04.04
TD0168
NIT Technical Decision for Mandatory
requirement for CSR generation
CPP_ND_V1.0, CPP_FW_V1.0,
FIA_X509_EXT.3
2017.04.04
TD0167
NIT Technical Decision for Testing SSH
2^28 packets
CPP_ND_V1.0, CPP_FW_V1.0, ND SD
V1.0, FCS_SSHC_EXT.1.8,
FCS_SSHS_EXT.1.8, FMT_SMF.1
2017.04.04
TD0164
NIT Technical Decision for Negative
testing for additional ciphers for SSH
CPP_ND_V1.0, ND SD V1.0,
FCS_SSHC_EXT.1.4,
FCS_SSHS_EXT.1.4
2017.03.21
TD0160
NIT Technical Decision for Transport
mode and tunnel mode in IPSEC
communications
CPP_ND_V1.0, CPP_FW_V1.0,
FCS_IPSEC_EXT.1.3
2017.03.08
55
TD0156
NIT Technical Decision for SSL/TLS
Version Testing in the NDcPP v1.0 and
FW cPP v1.0
CPP_ND_V1.0, CPP_FW_V1.0, ND SD
V1.0, FCS_TLSS_EXT1.2,
FCS_TLSS_EXT.2.2
2017.03.15
TD0155
NIT Technical Decision for TLSS tests
using ECDHE in the NDcPP v1.0.
CPP_ND_V1.0, ND SD V1.0,
FCS_TLSS_EXT.1.3, FCS_TLSS_EXT.2.3
2017.03.01
TD0154
NIT Technical Decision for Versions of
TOE Software in the NDcPP v1.0 and FW
cPP v1.0
CPP_ND_V1.0, CPP_FW_V1.0,
FPT_TUD_EXT.1
2017.03.01
TD0153
NIT Technical Decision for Auditing of
NTP Time Changes in the NDcPP v1.0
and FW cPP v1.0
CPP_ND_V1.0, CPP_FW_V1.0,
FAU_GEN.1, FPT_STM.1
2017.03.01
TD0152
NIT Technical Decision for Reference
identifiers for TLS in the NDcPP v1.0 and
FW cPP v1.0
CPP_ND_V1.0, CPP_FW_V1.0, ND SD
V1.0, FCS_TLSC_EXT.1,
FCS_TLSC_EXT.2
2017.03.01
TD0151
NIT Technical Decision for
FCS_TLSS_EXT Testing - Issue 1 in
NDcPP v1.0.
CPP_ND_V1.0, ND SD V1.0,
FCS_TLSS_EXT.1, FCS_TLSS_EXT.2
2017.03.01
TD0150
NIT Technical Decision for Removal of
SSH re-key audit events in the NDcPP
v1.0 and FW cPP v1.0
CPP_ND_V1.0, CPP_FW_V1.0,
FAU_GEN.1
2017.03.01
TD0143
NIT Technical Decision for Failure testing
for TLS session establishment in NDcPP
and FWcPP
FCS_TLSS_EXT.1.1, CPP_ND_V1.0,
CPP_FW_V1.0,
2017.01.18
TD0130
NIT Technical Decision for Requirements
for Destruction of Cryptographic Keys
CPP_ND_V1.0, CPP_FW_V1.0,
FCS_CKM.4
2016.12.08
TD0126
NIT Technical Decision for TLS Mutual
Authentication
CPP_ND_V1.0, CPP_FW_V1.0,
FTP_ITC.1, FCS_TLSC_EXT.1
2016.11.30
TD0125
NIT Technical Decision for Checking
validity of peer certificates for HTTPS
servers
CPP_ND_V1.0, CPP_FW_V1.0, , ND SD
v1.0, FCS_HTTPS_EXT.1.2
2016.11.15
TD0117
NIT Technical Decision for
FIA_X509_EXT.1.1 Requirement in
NDcPP
CPP_ND_V1.0, CPP_ND_V1.0,
FIA_X509_EXT, FPT_TST_EXT,
FPT_TUD_EXT
2016.10.13
TD0116
NIT Technical Decision for a Typo in
reference to RSASSA-PKCS1v1_5 in
NDcPP and FWcPP
CPP_ND_V1.0, CPP_FW_V1.0,
FCS_COP.1.1(2)
2016.10.13