PREMIER MINISTRE General Secretariat for Defence and National Security French Network and Information Security Agency Certification Report ANSSI-CC-2010/19 CC IDeal Citiz SmartCard (on SB23YR80B), version 1.4.5 IAS application Paris, 9th April 2010 Courtesy Translation Certification report ANSSI-CC-2010/19 CC IDeal Citiz SmartCard (on SB23YR80B), version 1.4.5 Page 2 out 17 CER/F/07.5 Warning This report is designed to provide sponsors with a document enabling them to assess the security level of a product under the conditions of use and operation defined in this report for the evaluated version. It is also designed to provide the potential purchaser of the product with the conditions under which he may operate or use the product so as to meet the conditions of use for which the product has been evaluated and certified; that is why this certification report must be read alongside the evaluated user and administration guidance, as well as with the product security target, which presents threats, environmental assumptions and the supposed conditions of use so that the user can judge for himself whether the product meets his needs in terms of security objectives. Certification does not, however, constitute a recommendation product from ANSSI (French Network and Information Security Agency), and does not guarantee that the certified product is totally free of all exploitable vulnerabilities. Any correspondence about this report has to be addressed to: Secrétariat Général de la Défense et de la Sécurité Nationale Agence nationale de la sécurité des systèmes d'information Centre de certification 51, boulevard de la Tour Maubourg 75700 PARIS cedex 07 SP France certification.anssi@ssi.gouv.fr Reproduction of this document without any change or cut is authorised. CC IDeal Citiz SmartCard (on SB23YR80B), version 1.4.5 Certification report ANSSI-CC-2010/19 Page 3 out 17 Certification report reference ANSSI-CC-2010/19 Product name CC IDeal Citiz SmartCard (on SB23YR80B) Product reference, version IDEAL/ST23YR80/1.4.5, Version 1.4.5 Protection profile conformity [PP0005], Secure Signature-Creation Device Type 2, version 1.04 [PP0006], Secure Signature-Creation Device Type 3, version 1.05 Evaluation criteria and version Common Criteria version 3.1 Evaluation level EAL 5 augmented ALC_DVS.2, AVA_VAN.5 Developers SAGEM Sécurité Etablissement d’Osny, 18 Chaussée Jules César, 95520 Osny, France ST Microelectronics 29 Boulevard Romain Rolland, 75669 Paris cedex 14, France Sponsor SAGEM Sécurité Etablissement d’Osny, 18 Chaussée Jules César, 95520 Osny, France Evaluation facility CEA - LETI 17 rue des martyrs, 38054 Grenoble Cedex 9, France Phone: +33 (0)4 38 78 40 87, email : cesti.leti@cea.fr Recognition arrangements CCRA The product is recognised at EAL4 level. SOG-IS Certification report ANSSI-CC-2010/19 CC IDeal Citiz SmartCard (on SB23YR80B), version 1.4.5 Page 4 out 17 CER/F/07.5 Introduction The Certification Security certification for information technology products and systems is governed by decree number 2002-535 dated April, 18th 2002, and published in the "Journal Officiel de la République Française". This decree stipulates that: • The French Network and Information Security Agency draws up certification reports. These reports indicate the features of the proposed security targets. They may include any warnings that the authors feel the need to mention for security reasons. They may or may not be transmitted to third parties or made public, as the sponsors desire (article 7). • The certificates issued by the Prime Minister certify that the copies of the products or systems submitted for evaluation fulfil the specified security features. They also certify that the evaluations have been carried out in compliance with applicable rules and standards, with the required degrees of skill and impartiality (article 8). The procedures are available on the Internet site www.ssi.gouv.fr. CC IDeal Citiz SmartCard (on SB23YR80B), version 1.4.5 Certification report ANSSI-CC-2010/19 Page 5 out 17 Content 1. THE PRODUCT........................................................................................................................... 6 1.1. PRESENTATION OF THE PRODUCT........................................................................................... 6 1.2. EVALUATED PRODUCT DESCRIPTION ..................................................................................... 6 1.2.1. Product identification.................................................................................................... 6 1.2.2. Security services............................................................................................................ 7 1.2.3. Architecture................................................................................................................... 7 1.2.4. Life cycle ....................................................................................................................... 8 1.2.5. Evaluated configuration................................................................................................ 9 2. THE EVALUATION.................................................................................................................. 10 2.1. EVALUATION REFERENTIAL ................................................................................................. 10 2.2. EVALUATION WORK ............................................................................................................. 10 2.3. CRYPTOGRAPHIC MECHANISMS ROBUSTNESS ANALYSIS..................................................... 10 2.4. RANDOM NUMBER GENERATOR ANALYSIS .......................................................................... 10 3. CERTIFICATION...................................................................................................................... 11 3.1. CONCLUSION........................................................................................................................ 11 3.2. RESTRICTIONS...................................................................................................................... 11 3.3. RECOGNITION OF THE CERTIFICATE..................................................................................... 11 3.3.1. European recognition (SOG-IS).................................................................................. 11 3.3.2. International common criteria recognition (CCRA)................................................... 12 ANNEX 1. EVALUATION LEVEL OF THE PRODUCT.......................................................... 13 ANNEX 2. EVALUATED PRODUCT REFERENCES .............................................................. 15 ANNEX 3. CERTIFICATION REFERENCES ........................................................................... 17 Certification report ANSSI-CC-2010/19 CC IDeal Citiz SmartCard (on SB23YR80B), version 1.4.5 Page 6 out 17 CER/F/07.5 1. The product 1.1. Presentation of the product The evaluated product is the « CC IDeal Citiz smartcard (on SB23YR80B), IDEAL/ST23YR80/1.4.5, Version 1.4.5 » developed by SAGEM Sécurité and ST Microelectronics. The evaluated product is a dual smartcard (contact and contactless). It is composed of: - three applications : o the AIP application which performs the pre-personalization and the personalization operations of the smartcard. This application is not accessible once in Operational Use phase, o the ICAO application which implements the machine readable travel document features and which may be instantiated several times on the product, o the IAS (Identity Authentication Signature) application which allows to generate, destroy and load keys to generate digital signature. - and an opened JacaCard System which allows to load applets on the product during its Operational Use phase. 1.2. Evaluated product description The security target [ST] defines the evaluated product, its evaluated security functionalities and its operational environment. The security target is conformant to the[PP0005] and [PP0006] protection profiles, adapted to the CC version 3.1 (as those PP hase been xritten accpording to the CC version 2.1) 1.2.1. Product identification The configuration list [CONF] identifies the product’s constituent elements. The certified version of the product can be identified by the following elements: - product’s name and version : CC Ideal Citiz, version 1.4.5; - microcontroller’s name and version: SB23YR80B; - commercial reference (SAGEM) : IDEAL/ST23YR80/1.4.5; - whole embededd software reference (SAGEM ORGA) OFFICIEL_IDEAL_ST23YR80_1_4_50; - ST Microelectronics reference: SB23YR80 QPX (masked chip). Every version of the software components of the certified version of the product can be checked according to the command and responses identified in the installation guidance of the product (see [GUIDES]). CC IDeal Citiz SmartCard (on SB23YR80B), version 1.4.5 Certification report ANSSI-CC-2010/19 Page 7 out 17 1.2.2. Security services The TOE provides mainly the following evaluated security services: o generation of private and public signing keys ; o destruction of the private and public signing keys ; o import of private signing key ; o signature creation (based on RSA or elliptic curves mechanisms); o and PIN authentication of the signatory. 1.2.3. Architecture The product consists of - the SB23YR80B microcontroller, developed and produced by ST Microelectronics ; - software parts, developed by SAGEM Sécurité, which CVS reference is OFFICIEL_IDEAL_ST23YR80_1_4_00, masked in the microcontroller’s ROM, composed of: o the OPUCE operating system; o the HAL hardware abtract layer; o the JacaCard System; o the AIP card initialization and personalization application; o and the IAS and ICAO applications ; - the IAS application patch, version 5.0, developed by SAGEM Sécurité, loaded into the microcontroller’s EEPROM. The TOE is the IAS Application, together with the functions/services provided by the operating system and the microcontroller IC required to support the applet functionalities. Application manager IAS application IAS instance 1 AIP Instance ICAO Data ICAO instance ICAO application IAS Data n AIP application AIP Data Deactivated in user phase IAS Data 1 IAS instance n Operating System HAL JCS (VM JCRE) VGP Operating System AIP Specific ICAO specific IAS Specific TOE Application manager IAS application IAS instance 1 AIP Instance ICAO Data ICAO instance ICAO application IAS Data n AIP application AIP Data Deactivated in user phase IAS Data 1 IAS instance n Operating System HAL JCS (VM JCRE) VGP Operating System AIP Specific ICAO specific IAS Specific TOE Certification report ANSSI-CC-2010/19 CC IDeal Citiz SmartCard (on SB23YR80B), version 1.4.5 Page 8 out 17 CER/F/07.5 The evaluation facility verified the isolation between the various applications, notably between those in the TOE with those not included in the TOE. The evaluation facility verified that a Java applet could only access to its own data and not to those belonging to another applet. 1.2.4. Life cycle The product’s life cycle is organised as follow: Patch loading is protected by the AIP application. Phase 1 Phase 2 Phase 3 Phase 4 Embedded software development Development IC design and dedicated software development Integration Photomask fabrication IC packaging and initialization IC manufacturing, test and possible pre - personalization IC pre-personalization: Create application/ Create LDS File System Personalization Usage End of life Manufacturing Step 1 Personalization Usage Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Legend Trusted delivery and verification procedures Delivery supposed to be done within secure environment Legend Trusted delivery and verification procedures Delivery supposed to be done within secure environment SAGEM (Osny) STM (Rousset, Singapour, Zaventem) STM (Rousset) DPE Agrape DPE Tokyo STM (Rousset) Patch development Phase 1 Phase 2 Phase 3 Phase 4 Embedded software development Development IC design and dedicated software development Integration Photomask fabrication IC packaging and initialization IC manufacturing, test and possible pre - personalization IC pre-personalization: Create application/ Create LDS File System Personalization Usage End of life Manufacturing Step 1 Personalization Usage Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Legend Trusted delivery and verification procedures Delivery supposed to be done within secure environment Legend Trusted delivery and verification procedures Delivery supposed to be done within secure environment SAGEM (Osny) STM (Rousset, Singapour, Zaventem) STM (Rousset) DPE Agrape DPE Tokyo STM (Rousset) Patch development CC IDeal Citiz SmartCard (on SB23YR80B), version 1.4.5 Certification report ANSSI-CC-2010/19 Page 9 out 17 The embedded software has been developed on the following site: SAGEM Sécurité - Etablissement d’Osny 18 Chaussée Jules César 95520 Osny France The microcontroller development sites are identified in the [2010/02] certification report. 1.2.5. Evaluated configuration The certificate applies to the opened configuration of this product (applets can be loaded on the product in operational phase, phase 7). The product tested by the evaluation facility is typical to the final product. Certification report ANSSI-CC-2010/19 CC IDeal Citiz SmartCard (on SB23YR80B), version 1.4.5 Page 10 out 17 CER/F/07.5 2. The evaluation 2.1. Evaluation referential The evaluation has been performed in compliance with Common Criteria version 3.1 [CC] and with the Common Evaluation Methodology [CEM] In order to meet the specificities of smart cards, the [CC AP] and [COMP] guides have been applied. 2.2. Evaluation work The evaluation has been performed according to the composition scheme as defined in the guide [COMP] in order to assess that no weakness comes from the integration of the software in the microcontroller already certified. Therefore, the results of the evaluation of the microcontroller “SB23YR80B with Neslib version 3.0” at EAL6 level augmented with ALC_FLR.1, compliant with the [PP0035] protection profile, have been used. This microcontroller has been certified the 10 February 2010 under the reference ANSSI-CC-2010/02. The maintenance report ANSSI-2010/02-M01 has also been issued the 19th March 2010 for this product. The evaluation technical report [ETR], delivered to ANSSI the 2nd April 2010, provides details on the work performed by the evaluation facility and assesses that all evaluation tasks are “pass”. 2.3. Cryptographic mechanisms robustness analysis The robustness of cryptographic mechanisms has been analysed by ANSSI according to [REF-CRY]. The results are stated in the cryptographic analysis report [ANA-CRY] which concludes that: - the ECDSA signature schema offered by this product does not conform to the referential; - signature must be generated using the SHA-256 function; - RSA modules and elliptic curves must be sized according to the referential rules; - For the RSA signature schema, it is recommended to use a public exponent higher than 216. Those results have been taken into account in the evaluator independent vulnerability analysis and had not leaded to the identification of exploitable vulnerability for the aimed AVA_VAN level. 2.4. Random number generator analysis The random number generator used by this product is the one provided by the microcontroller (see [2010/02] certification report). CC IDeal Citiz SmartCard (on SB23YR80B), version 1.4.5 Certification report ANSSI-CC-2010/19 Page 11 out 17 3. Certification 3.1. Conclusion The evaluation was carried out according to the current rules and standards, with the required competency and impartiality of a licensed evaluation facility. All the work performed permits the release of a certificate in conformance with the decree 2002-535. This certificate testifies that the “CC IDeal Citiz SmartCard (on SB23YR80B), version 1.4.5” submitted for evaluation fulfils the security features specified in its security target [ST] for the evaluation level EAL 5 augmented. 3.2. Restrictions This certificate only applies on the product specified in chapter 1.2 of this certification report. The user of the certified product shall respect the security objectives for the operational environment specified in the security target [ST] at the 4.2 and 4.3 chapters, and shall respect the recommendations in the guidance [GUIDES]. 3.3. Recognition of the certificate 3.3.1. European recognition (SOG-IS) This certificate is released in accordance with the provisions of the SOG-IS agreement [SOG- IS]. The European Recognition Agreement made by SOG-IS in 1999 allows recognition from Signatory States of the agreement1 , of ITSEC and Common Criteria certificates. The European recognition is applicable up to ITSEC E6 and CC EAL7 levels. The certificates that are recognized in the agreement scope are released with the following marking: 1 The signatory countries of the SOG-IS agreement are: Finland, France, Germany, Greece, Italy, The Netherlands, Norway, Spain, Sweden and United Kingdom. Certification report ANSSI-CC-2010/19 CC IDeal Citiz SmartCard (on SB23YR80B), version 1.4.5 Page 12 out 17 CER/F/07.5 3.3.2. International common criteria recognition (CCRA) This certificate is released in accordance with the provisions of the CCRA [CC RA]. The Common Criteria Recognition Arrangement allows the recognition, by signatory countries1 , of the Common Criteria certificates. The mutual recognition is applicable up to the assurance components of CC EAL4 level and also to ALC_FLR family. The certificates that are recognized in the agreement scope are released with the following marking: 1 The signatory countries of the CCRA arrangement are: Australia, Austria, Canada, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, India, Israel, Italy, Japan, the Republic of Korea, Malaysia, Netherlands, New-Zealand, Norway, Pakistan, Singapore, Spain, Sweden, Turkey, the United Kingdom and the United States of America. CC IDeal Citiz SmartCard (on SB23YR80B), version 1.4.5 Certification report ANSSI-CC-2010/19 Page 13 out 17 Annex 1. Evaluation level of the product Components by assurance level Assurance level of the product Class Family EAL 1 EAL 2 EAL 3 EAL 4 EAL 5 EAL 6 EAL 7 EAL 5+ Name of the component ADV_ARC 1 1 1 1 1 1 1 Security architecture description ADV_FSP 1 2 3 4 5 5 6 5 Complete semi-formal functional specification with additional error information ADV_IMP 1 1 2 2 1 Implementation representation of the TSF ADV_INT 2 3 3 2 Well-structured internals ADV_SPM 1 1 ADV Developmentt ADV_TDS 1 2 3 4 5 6 4 Semiformal modular design AGD_OPE 1 1 1 1 1 1 1 1 Operational user guidance AGD Guidance AGD_PRE 1 1 1 1 1 1 1 1 Preparative procedures ALC_CMC 1 2 3 4 4 5 5 4 Production support, acceptance procedures and automation ALC_CMS 1 2 3 4 5 5 5 5 Development tools CM coverage ALC_DEL 1 1 1 1 1 1 1 Delivery procedures ALC_DVS 1 1 1 2 2 2 Sufficiency of security measures ALC_FLR ALC_LCD 1 1 1 1 2 1 Developer defined life-cycle model ALC Life-cycle support ALC_TAT 1 2 3 3 2 Compliance with implementation standards ASE_CCL 1 1 1 1 1 1 1 1 Conformance claims ASE_ECD 1 1 1 1 1 1 1 1 Extended components definition ASE_INT 1 1 1 1 1 1 1 1 ST introduction ASE_OBJ 1 2 2 2 2 2 2 2 Security objectives ASE_REQ 1 2 2 2 2 2 2 2 Derived security requirements ASE_SPD 1 1 1 1 1 1 1 Security problem definition ASE Security Target Evaluation ASE_TSS 1 1 1 1 1 1 1 1 TOE summary specification ATE_COV 1 2 2 2 3 3 2 Analysis of coverage ATE_DPT 1 1 3 3 4 3 Testing: modular design ATE_FUN 1 1 1 1 2 2 1 Functional testing ATE Tests ATE_IND 1 2 2 2 2 2 3 2 Independent testing: sample Certification report ANSSI-CC-2010/19 CC IDeal Citiz SmartCard (on SB23YR80B), version 1.4.5 Page 14 out 17 CER/F/07.5 Components by assurance level Assurance level of the product Class Family EAL 1 EAL 2 EAL 3 EAL 4 EAL 5 EAL 6 EAL 7 EAL 5+ Name of the component AVA Vulnerability assessment AVA_VAN 1 2 2 3 4 5 5 5 Focused vulnerability analysis CC IDeal Citiz SmartCard (on SB23YR80B), version 1.4.5 Certification report ANSSI-CC-2010/19 Page 15 out 17 Annex 2. Evaluated product references [ST] Reference security target for the evaluation: - « Common Criteria security target – IAS ECC – Secure Signature Creation Device – CC IDeal Citiz », référence SSE- 0000067225, révision 07, For the needs of publication, the following security target has been provided and validated in the evaluation: - « Common Criteria security target lite – IAS ECC – Secure Signature Creation Device – CC IDeal Citiz », référence SSE- 0000078618, révision 03. [ETR] Evaluation technical report : - « EOS - Rapport Technique d’Evaluation », référence LETI.CESTI.EOS.RTE.001, édition 1.0, - « Réévaluation EOS - Rapport Technique d’Evaluation », référence LETI.CESTI.EOS.RTE.002, édition 2.1. [ANA-CRY] « Cotation de mécanismes cryptographiques- Qualification EOS », n° 805/ANSSI/ACE/LCC du 2 avril 2010. [CONF] « IDEAL_– Software Release Sheet – V1.4.50», référence SSE- 0000075528, révision 14. [GUIDES] Installation guidance: - «« IDEAL 1.4 procédure d’installation », référence SSE- 0000076822, version 01, Administration guidance: - « ICAO Application Pre-personalization manual - Project : CC Ideal Pass », référence SSE-0000074722, version 02, - « IDEAL IAS ECC Personalization Guidance », référence : SSE-0000064845, version 02, - « ICAO Application Personalization manual - Project : CC Ideal Pass », référence SSE-0000074723, version 04, User guidance: - « ICAO Application User manual - Project : CC Ideal Pass », référence SSE-0000074862, version 01, - « IDEAL IAS ECC Operational User Guidance », référence : SSE-0000065958, version 01. [PP0005] Protection Profile — Secure Signature-Creation Device Type 2, Version: 1.04, 25 July 2001. Certifié par le BSI (Bundesamt für Sicherheit in der Informationstechnik) sous la référence BSI-PP-0005- 2002. [PP0006] Protection Profile — Secure Signature-Creation Device Type 3, Version: 1.05, 25 July 2001. Certifié par le BSI sous la référence BSI- PP-0006-2002. Certification report ANSSI-CC-2010/19 CC IDeal Citiz SmartCard (on SB23YR80B), version 1.4.5 Page 16 out 17 CER/F/07.5 [PP0035] Protection Profile, Security IC Platform Protection Profile Version 1.0 June 2007. Certified by BSI (Bundesamt für Sicherheit in der Informationstechnik) under the reference BSI-PP-0035-2007. [2010/02] Certification report ANSSI-CC-2010/02, issued the 10th February 2010 for the “SA23YR48/80B and SB23YR48/80B, secured microcontrollers including the cryptographic libray NesLib v2.0 or v3.0 in SA or SB configuration”. [2010/02- M01] Maintenance report ANSSI-2010/02-M01, issued the 19th March 2010, related to the ANSSI-CC-2010/02 certificate. CC IDeal Citiz SmartCard (on SB23YR80B), version 1.4.5 Certification report ANSSI-CC-2010/19 Page 17 out 17 Annex 3. Certification references Decree number 2002-535 dated 18th April 2002 related to the security evaluations and certifications for information technology products and systems. [CER/P/01] Procedure CER/P/01 - Certification of the security provided by IT products and systems, DCSSI. [CC] Common Criteria for Information Technology Security Evaluation : Part 1: Introduction and general model, September 2006, version 3.1, revision 1, ref CCMB-2006-09-001, Part 2: Security functional components, September 2007, version 3.1, revision 2, ref CCMB-2007-09-002, Part 3: Security assurance components, September 2007, version 3.1, revision 2, ref CCMB-2007-09-003. [CEM] Common Methodology for Information Technology Security Evaluation : Evaluation Methodology, September 2007, version 3.1, revision 2, ref CCMB-2007-09-004. [CC AP] Common Criteria Supporting Document - Mandatory Technical Document - Application of attack potential to smart-cards, reference CCDB-2009-03-001 version 2.7 revision 1, March 2009 [COMP] Common Criteria Supporting Document - Mandatory Technical Document - Composite product evaluation for smart cards and similar devices, reference CCDB-2007-09-001 version 1.0, revision 1, September 2007. [CC RA] Arrangement on the Recognition of Common criteria certificates in the field of information Technology Security, May 2000. [SOG-IS] «Mutual Recognition Agreement of Information Technology Security Evaluation Certificates», version 2.0, April 1999, Management Committee of Agreement Group. [REF-CRY] Cryptographic mechanisms - Rules and recommendations about the choice and parameters sizes of cryptographic mechanisms with standard robustness level version 1.11, 24th of October 2008, see www.ssi.gouv.fr